GSM Home Alarm System with Photo-taking User’s Manual Profile For a better understanding of this product, please read this user manual thoroughly before using it. This Excellent GSM + Camera alarm system bases on the GSM network, integrates the communication technology, can automatically take photos of the intruders or burglars and send it to cell phone, so the user can easily see who break into their protected areas(home, office, factory, shop and so on). This is the unique feature of the security products! Features: 1. Adopt tri-band, GSM 900Mhz/1800Mhz/1900Mhz, alarm remotely without the limit of distance. 2. Support GSM/CDMA, remotely control the main panel to arm/ disarm/listen-in/photo-taking by SMS. 3. Support the motion detection function which Can capture thief ‘s photo and send to owner’s cell phone or email box, or stored into the SD card for evidence. 4. The picture to be transmitted adjustable: QCIF (160x128), CIF (320x240), VGA (640x480). 5. Can pre-set 5 groups of alarm Phone Numbers. 6. Listen-in function: Can clearly hear the voice, footstep, and so on. 7. With password input, can arm/ disarm/listen-in/photo-taking the alarm system by remote controllers and SMS. 8. Can control home appliances remotely through the relay output. 9. Main panel has two input ports, which can connect with wired devices (normally open). 10. Siren port for shift between silence and siren. 11. Can work with wireless detectors or sensors like PIR - l - Sensors, beams, gas/smoke detectors, panic buttons and so on. 12. All the alarm system with wireless signal transmission, no need to connect to wire and easy for installation. 13. Especially suitable for storeroom, garage and the places where have no telephone line. 14. Aesthetic metal cover with neat design, endurable and stable application. How to identify the ports of the main panel? 1. Power adapter socket, connect to 12V/ 1.2A direct current. 2. MIC: for listen-in function. 3. 10-pin ports: ANT; Vd; GND; SPEAKER; RELAYa1; RELAYa2; RELAYb1; RELAYb2;I1; I2 The first port—Signal line, For enhancement of the wireless signal of remote controller; The second port—Power output:12V 300MAH; The third port—Ground line˄black line for siren˅; The fourth port— audio output, connect to siren˄red - 2 - line for siren˅; The fifth and sixth ports— relay output(1,2), normally open, Users can remotely control air-conditioner, electric cooker; The seventh and eighth ports----relay output(3,4), normally open and will close for three minutes when alarm triggered, can connect to lamp˗also can remotely control appliance. The ninth and tenth ports----wire input ports, normally open, short circuit closed will trigger alarm. 4. Camera: contain VD, Tx, Rx,GND. 5. Reset: The alarm system will come back to the original settings when keep press the RESET button and then power on the main panel, all coded information will be deleted. original password is 123456. 6. SD card: for image information storage 7. LED light: green light show main panel under disarm status; green light flash slowly show main panel under arm status, while flash red light show alarm triggered. 8. SIM card: press the yellow point next to the SIM port, the SIM tray will come out, put into the SIM card and insert the tray. 9. Antenna: You should connect the antenna before power on the main panel. 10. ON/OFF How to start the base? 1. Delete all telephone Numbers and messages in the SIM card memory or buy a new card. insert SIM card - 3 - into the base before power on it. 2. Connect Camera and antenna with the base. 3. Format the SD card in FAT32. Insert the SD card to the SD card slot. 4. Connect to the 12V power supply, switch ON the main panel, the signal status LED turns to orange, after about 20 seconds, the signal status LED flash in orange, main panel will start to check the SIM card and search for GSM network. 5. LED light status: Flash red quickly: check camera Keep still in green: check OK, enter disarm state automatically Flash green slowly: under arm state Flash red: alarm state Flash red slowly: SMS sending Flash red quickly: MMS sending How to setup the alarm phone numbers and SMS? 1. you can send a SMS message to the base to setup the 5 groups of alarm phone numbers and 6 kinds of SMS .The SMS format: password #operation code # content # 123456#51# 13905950001#. save first group alarm phone number into the base. 123456#52# 13905950002#. save second group alarm phone number into the base. 123456#53# 13905950003#. save third group alarm phone number into the base. 123456#54# 13905950004#. save fourth group alarm - 4 - phone number into the base. 123456#55# 13905950005#. save fifth group alarm phone number into the base. 2. you can send a SMS message to the base to setup 6 kinds of SMS The first two message are for wired port I1, I2; The third message is for motion-detecting on spot when trigger alarm; The fourth message for wireless detectors (door sensors, PIR Sensors and remote controllers) when trigger alarm( 1 to 16 defense zone); The fifth is for emergency help triggered on remote controller. Every message cannot excess 10 Chinese characters or 20 English characters. If use the RESET button to reset the main panel, all messages will back to the default message as follows: Port I 1 triggered, the message is: ZONE 1 Activated. Port I 2 triggered, the message is: ZONE 2 Activated. Spot motion detect triggered, it is: Image Activated. Wireless detectors triggered, the message is: Wireless Activated. Emergency help triggered, the message will be: Emergency Activate.(it can be changed) You can rewrite the SMS messages: 123456#81# Front door open #. save the first group message instead of “ZONE1 Activated”. 123456#82# middle door open#. Save the second group message instead of “ZONE2 Activated”. - 5 - 123456#84# Camera working#. save the three group message instead of “Image Activated”. 123456#85# Window open#. Save the fourth group message instead of “Wireless Activated”. How to test the base alarm ? 1. The main panel will default in Disarm status when power on, you can arm it through remote control or send SMS (123456#1#1#).Under the Arm state, with green LED flash slowly, any wired input (I1, I2) touches ground, or any wireless detectors triggered, or move around on the spot before the camera, the alarm system will start to take photos, send SMS and dial out stored telephone numbers. 2. It will send SMS and MMS before dial alarm phone numbers. If the SMS and MMS function has been closed or limited, It will dial out the preset telephone numbers only. you can through the disarm key on remote controller to retreat from alarm state. 3. When there is alarm calling in, you can put through the phone to listen-in, input 3# 1# on your phone to make the main panel sound the siren and 3# 0# to stop siren, 4#1# to listen-in on spot. How to control the main panel by calling ? Call in the base and input password 123456# , then input the following commands to set the base: - 6 - Com Function Com Function 1#1# Arm 1#0# Disarm * 2# --# Apply for pictures(1—20 optional), 2#1# means for 1 picture 3#1# Start siren to sound immediately remotely 3#0# Stop Siren sounding remotely 4#1# Start to listen-in 4#0# Stop listen-in 11#1# Set siren sound when alarm * 11#0# Set siren not sound when alarm 12#1# Set send SMS when alarm * 12#0# Not Send SMS when alarm 13#1# Set send MMS when alarm * 13#0# Not Send MMS when alarm 15#1# Dial phone numbers when alarm * 15#0# Not dial phone numbers when alarm 21#--# Set picture size(0—2), 0 --for160x128; 1*-- for 320x240; 2 --for 640x480 22#--# Times of photo-taking when alarm(1—20 optional), 22#1# means send 1 pictures when alarm * 23#1# Set the IR back light on 23#0# Set the IR back light off * 24#1# Set camera motion 23#0# Set camera motion detect - 7 - detect function on * function off 27#--# Set the sensitivity of camera(1—99),.1 is high sensitivity and 99 is low sensitivity, default 15 * 30# Show arm or disarm status of zones 31#--# Change password. Enter a new password (1—6 bit). 32#1# Set ENGLISH version 32#0# Set CHINESE version * 38#--# Set arm of zone (wireless zone: 1—16; wire zone: 21—23) 39#--# Set disarm of zone (wireless zone: 1—16; wire zone: 21—23) 40## Check MMS setup in the base (content of 41#----46#) 41#--# Set Access Point Node (APN): 42#--# Set MMS User name (User): 43#--# Set MMS User Password (Pass): 44#--# Set MMS Centre IP Address (IP): 45#--# Set Port of MMS Centre IP Address (Port): 46#--# Set MMS Homepage (MMS Home): 50## show preset phone numbers in the base 51#--# First group phone number(0—15bit) 52#-- # Second group phone number(0—15bit) 53#--# Third group phone number(0—15bit) 54#-- # fourth group phone number(0—15bit) 55#--# Fifth group phone number(0—15bit) 60## show Email address in the base - 8 - 61#--# Set First Email address(0—31bit) 62#-- # Set Second Email address(0—31bit) 80## show preset SMS in the base 81#--# First group Message(0—24bit) when wire port I1 alarm 82#-- # Second group Message(0—24bit) when wire port I2 alarm 84#--# fourth group Message(0—24bit) when camrea alarm 85#-- # Fourth group Message(0—24bit) when wireless alarm 86#--# Message(0—20bit) for emergency 90## show Output status in the base 92#1# Set output(1,2) to high (Relay close) 92#0# Set output(1,2) to low (Relay open) 94#1# Set output(3,4) to high 94#0# Set output(3,4)4to low Note: 1. In above table, ‘ * ’ stand for default settings. 2. In the above phone operation, one long beep shows successful, two short beeps shows failed, you should try again. 3. In the above phone dialing-in operation commands, some commonds operation also suitable for SMS input ( see below). How to setup the Special function of the base by SMS? - 9 - You can send a SMS message to the SIM card to set the base, format is: Password # Command order #Parameter#. Eg:123456#1#1#, remotely set the main panel into Arm status. 123456#21#2#, set the size of the picture is 640x480(big size). 123456#31#888888#, change the password into 888888. After the host received the message,it will do the sets as the message content and reply a message for confirmation, so user will know the working status of the system. The replied message as follows: Disarm, Siren-ON, SMS-ON, MMS-ON, Phone-ON, Pic-Middle; Pic-1,Infraled-OFF, Pic-Moniter-ON, Cam-sensitivity15. Note: Set MMS parameter in the base. As in CHINA ---- MMS settings : Access Point Name(APN): CMWAP Gateway IP (proxy) address(IP): 10.0.0.172 Username: Password: MMS Message (Relay) Server URL: http:/mms.monternet.com 123456#41# CMWAP # Set GPRS Access point. 123456#42## Set MMS Uesr name. (empty) 123456#43## Set MMS Uesr Password. (empty) - l0 - 123456#44# 010.000.0000.172# Set IP Address. 123456#45#9201# Set Port , 123456#46#http:/mms.monternet.com # Set MMS Homepage. How to code the detectors? Power on the main panel, LED will keep green or flash green, you can press the reset key until the LED change from green to red. then you can start to register them. For door sensor, just move the two parts of door sensor, it will beep or flash red to show successful. And for PIR Sensors, turn the switch to “on” and the system will beep or flash red to show successful and then turn it to “off” to avoid wrong alarm. For remote controllers, press any button on its panel, and the system also beeps or flash red. For gas and smoke detectors, there is a black switch on the left side, you can press it to register it with base. How to add more detectors? You can add new sensors or detectors, such as wireless door sensors, PIR Sensors, gas and smoke detectors when you push the reset key untill the LED change from green to red. You should trigger every sensor or detector, and the red LED will flash every time you register a sensor or detector with main panel successfully. After you finish it,you can push the reset key again or waitting for 20 seconds, it will retreat and automatically enter into working state.(with green LED) How to cancel the lost detectors? - ll - In case of the coded sensors or detectors are lost, you can cancel the coded information of these detectors so that they can not control your alarm system. Keep pressing the reset button, then power on the system. one beep sound or LED flashes, shows reset is successful. All registered detectors have been deleted from the main panel. You can register them again with the above mentioned procedures. System reset will not change the SMS message. How to control the main panel with remote controllers? There are four or three keys on the remote controller: arm(Out arm and Home arm), disarm, emergency help. 1. When you press “arm”, the signal LED of the main panel will flashing green. shows it is in arm status, now it will alarm and dial out phone numbers if detector/sensors triggered or somebody go across in front of the camera, the LED will flashing in red. 2. When you press “disarm”, signal LED of main panel will turn to green and keep still. Now it won’t alarm and dial out phone numbers when detectors triggered. 3. When you press “Emergency help”, it will alarm and send MMS and SMS no matter it is under arm status or disarm status. The Signal LED will be red with flashing, which means it is alarming. . - l2 - Ďǃ Components list main panel 1pcs remote controllers, 2pcs wireless door sensor 1pcs wireless PIR detector, 1pcs alarm siren 1 pcs camera, 1pcs GSM antenna 1 pcs 12v DC adaptor 1pcs user manual 1pcs The following sensors can be optional: - l3 - Optional sensors/detectors are packed separately. It includes remote controllers,outdoor siren,transmitter, wireless PIR, wireless gap sensor, wireless gas detector, wireless smoke detector, panic button, baluster, etc. you may buy according your specific requirements. - l4 - VII. Technical Parameters Main Panel Stand-to current: 50mA. Working volt. : 9V-12V Working temperature: -40§—85§ Support GSM900, 1800, and 1900Mhz., three working modes. Support PHASE 2/2 agreement (including data business) Sending power: Class10 (2 w)/ EGSM900 and CLASS 1(1W)/GSM1800 Receiving code: ASK Receiving frequency: 315 and 433Mhz. Remote distance: 100 meters. Wireless Gap Detector (Door / Window Contact) Power Supply: DC12V (inner 12V battery) Static Current: 20 mA Transmission Current: 15mA Transmission Frequency: 315/433MHZ±0.5MHZ Transmission Distance: No obstacle 80m Internal Distance: 15 mm Working Condition: Temperature –10ć~+ 40 ć Humidity 90% rh - l5 - Wireless P.IR Detector Power Supply: DC9V (inner 9V battery) Static Current: 100 mA Transmission Current: 20mA Transmission Frequency: 315/433MHZ±0.5MHZ Transmission Distance: No obstacle 80m Detective Speed: 0.3 - 3m/s Detective Distance: 5 - 12m Detective Range: Horizontal 110° Vertical 60° Working Condition: Temperature –10 ć~+ 40 ć Humidity 90 rh Remote Controller Power Supply˖DC=12V~8.4 ˄Inside A23 DC=12V dry battery˅ Static Current˖11=0 Emission Current˖1215 mA Emission Frequency˖f=315±0.2 MHz Emission Speed˖T1 second Emission Distance˖Without obstruct 80m Working Environment: Temperature -10ć̚+40ć Relative Humidity90% - l6 - FAQ Symptoms Causes Remedies Cannot alarm by phone 1. Hasn’t armed 2. Less than 30 seconds after arming. 3. Set wrong phone num 4. The two parts of door\window sensor is installed too far from each other. 5. Haven’t activated PIR. 6. Hasn’t checked code 1. Make arming 2. Operate after 30 seconds 3. Set the num again according to the manual 4. Adjust the installation place of the door sensor 5. Activate the PIR 6. Check code again Remote controlling distance is too short and the light indicator is not on strong enough 1. The battery of remote controller rustily 2. Low battery 1. Clean the rust 2. Change battery Light indicator of door sensor and PIR is always on. Low battery Change battery Dial alarm num slowly The main panel has stored others num Set it again according to the operation manual The main panel cannot receive accessories signals Hasn’t checked code Check the code again Notice˖ ŶDon’t install the system beside the strongly disturbing equipments like motor, computer etc. ŶShould be installed in a concealed place. ŶShould be plug firmly and ensure well dissipation ŶOnly designed for indoor - l7 -