index

BRITISH STANDARDS BS 4:Structural steel sections BS 4-1:2005 Specification for hot-rolled sections supersedes BS 4-1:1993 ISBN 0 580 46453 9 £32.00 members £64.00 non-members ISE/13 BS 4551:2005 Mortar. Methods of test for mortar. Chemical analysis and physical testing supersedes BS 4551-1:1998 and BS 4551-2:1998 ISBN 0 580 46454 7 £53.00 members £106.00 non-members B/519/2 BS 5261:Copy preparation and proof correction BS 5261-2:2005 Specification for typographic requirements, marks for copy preparation and proof correction, proofing procedure supersedes BS 5261-2:1976 ISBN 0 580 46570 5 £32.00 members £64.00 non-members PAI/43 BS 5261C:2005 Marks for copy preparation and proof correction supersedes BS 5261C:1976 £5.00 members £5.00 non-members PAI/43 A fold-out card giving the marks specified in Table 1 of BS 5261-2, together with notes on their use. VAT is applicable to this item. Discounts are available for bulk orders (£42 for 10, £79 for 20, £189 for 50, £325 for 100). BS 6001:Sampling procedures for inspection by attributes BS 6001-4:2005 System of sequential sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection partially supersedes BS 6001-4:1994 ISBN 0 580 46463 6 £64.00 members £128.00 non-members SS/5 BS 8432:2005 Spinal orthoses. Guide to design supersedes BS 5473:1977 ISBN 0 580 46050 9 £32.00 members £64.00 non-members SS/5 BS 8440:Health informatics. Medical digital imaging. Profiles format BS 8440-1:2005 General principles no current standard is superseded ISBN 0 580 46549 7 £26.00 members £52.00 non-members IST/35 BS 8440-2:2005 Particular requirements for metadata profiles no current standard is superseded ISBN 0 580 46550 0 £26.00 members £52.00 non-members IST/35 BS 8456:2005 Code of practice for design and installation of directional sounder evacuation systems no current standard is superseded ISBN 0 580 46416 4 £26.00 members £52.00 non-members CPL/34/9 BS EN 54-13:2005 Compatibility assessment of system components no current standard is superseded ISBN 0 580 46213 7 £46.00 members £92.00 non-members FSH/12,FSH/12/1 BS EN ISO 140:Acoustics. Measurement of sound insulation in buildings and of building elements BS EN ISO 140-11:2005 Laboratory measurements of the reduction of transmitted impact sound by floor coverings on lightweight reference floors no current standard is superseded ISBN 0 580 46445 8 £53.00 members £106.00 non-members EH/1/6 BS EN 1052:Methods of test for masonry BS EN 1052-5:2005 Determination of bond strength by the bond wrench method no current standard is superseded ISBN 0 580 46380 X £32.00 members £64.00 non-members B/519 BS EN 1168:2005 Precast concrete products. Hollow core slabs no current standard is superseded ISBN 0 580 46082 7 £64.00 members £128.00 non-members B/524 BS EN ISO 2063:2005 Thermal spraying. Metallic and other inorganic coatings. Zinc, aluminium and their alloys supersedes BS EN 22063:1994 ISBN 0 580 46219 6 £46.00 members £92.00 non-members STI/40 BS EN ISO 3815:Zinc and zinc alloys BS EN PUBLICATIONS BS EN 54:Fire detection and fire alarm systems BS EN PUBLICATIONS Page 1 of 69 BS EN ISO 3815-1:2005 Analysis of solid samples by optical emission spectrometry supersedes BS EN 12019:1998 which remains current ISBN 0 580 46225 0 £32.00 members £64.00 non-members NFE/8 BS EN ISO 5983:Animal feeding stuffs. Determination of nitrogen content and calculation of crude protein content BS EN ISO 5983-1:2005 Kjeldahl method supersedes BS 5766-4:1998 ISBN 0 580 46421 0 £32.00 members £64.00 non-members AW/10 BS EN ISO 5983-2:2005 Block digestion/steam distillation method no current standard is superseded ISBN 0 580 46420 2 £46.00 members £92.00 non-members AW/10 BS EN 10305:Steel tubes for precision applications. Technical delivery conditions BS EN 10305-6:2005 Welded cold drawn tubes for hydraulic and pneumatic power systems supersedes BS 6323-6:1982 ISBN 0 580 46097 5 £46.00 members £92.00 non-members ISE/8 BS EN 10311:2005 Joints for the connection of steel tubes and fittings for the conveyance of water and other aqueous liquids partially supersedes BS 534:1990 ISBN 0 580 46124 6 £46.00 members £92.00 non-members ISE/8 BS EN ISO 10664:2005 Hexalobular internal driving feature for bolts and screws supersedes BS EN ISO 10664:1999 ISBN 0 580 46442 3 £32.00 members £64.00 non-members FME/9/2 BS EN ISO 11064:Ergonomic design of control centres BS EN ISO 11064-6:2005 Environmental requirements for control centres no current standard is superseded ISBN 0 580 46422 9 £46.00 members £92.00 non-members PH/9 BS EN ISO 12625:Tissue paper and tissue products BS EN ISO 12625-3:2005 Determination of thickness, bulking thickness and apparent bulk density supersedes BS EN 12625-3:1999 ISBN 0 580 46435 0 £32.00 members £64.00 non-members PAI/11 BS EN ISO 12625-4:2005 Determination of tensile strength, stretch at break and tensile energy absorption supersedes BS EN 12625-4:1999 ISBN 0 580 46436 9 £32.00 members £64.00 non-members PAI/11 BS EN ISO 12625-9:2005 Determination of ball burst strength no current standard is superseded ISBN 0 580 46437 7 £32.00 members £64.00 non-members PAI/11 BS EN 12629:Machines for the manufacture of constructional products from concrete and calcium-silicate. Safety BS EN 12629-6:2004 Stationary and mobile equipment for the manufacture of precast reinforced products no current standard is superseded ISBN 0 580 46113 0 £53.00 members £106.00 non-members MCE/3/7 BS EN 12697:Bituminous mixtures. Test methods for hot mix asphalt BS EN 12697-43:2005 Resistance to fuel no current standard is superseded ISBN 0 580 46257 9 £32.00 members £64.00 non-members B/510/1 BS EN 12921:Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours BS EN 12921-4:2005 Safety of machines using halogenated solvents no current standard is superseded ISBN 0 580 46359 1 £53.00 members £106.00 non-members MCE/3/8 BS EN 13060:2004 Small steam sterilizers supersedes BS 3970-4:1990 ISBN 0 580 46187 4 £64.00 members £128.00 non-members LBI/35 BS EN 13367:2005 Ceramic machines. Safety. Transfer platforms and cars no current standard is superseded ISBN 0 580 46428 8 £46.00 members £92.00 non-members MCE/3/14 BS EN 13630:Explosives for civil uses. Detonating cords and safety fuses BS EN PUBLICATIONS Page 2 of 69 BS EN 13630-10:2005 Determination of initiating capability of detonating cords no current standard is superseded ISBN 0 580 46246 3 £26.00 members £52.00 non-members CII/61 BS EN 13796:Safety requirements for cableway installations designed to carry persons. Carriers BS EN 13796-3:2005 Fatigue tests no current standard is superseded ISBN 0 580 46155 6 £26.00 members £52.00 non-members MCE/20 BS EN 13885:2005 Food processing machinery. Clipping machines. Safety and hygiene requirements no current standard is superseded ISBN 0 580 46254 4 £60.00 members £120.00 non-members MCE/3/5 BS EN 14336:2004 Heating systems in buildings. Installation and commissioning of water based heating systems partially supersedes BS 5449:1990 ISBN 0 580 46251 X £53.00 members £106.00 non-members RHE/24 BS EN 14525:2004 Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, grey iron, steel, PVC-U, PE, fibre-cement no current standard is superseded ISBN 0 580 46203 X £53.00 members £106.00 non-members PSE/10 BS EN 14604:2005 Smoke alarm devices supersedes BS 5446-1:2000 which remains current ISBN 0 580 46651 5 £70.00 members £140.00 non-members FSH/12/2 BS EN PUBLICATIONS BS EN ISO 14630:2005 Non-active surgical implants. General requirements supersedes BS EN ISO 14630:1998 ISBN 0 580 46223 4 £46.00 members £92.00 non-members CH/150 BS EN 14662:Ambient air quality. Standard method for measurement of benzene concentrations BS EN 14662-5:2005 Diffusive sampling followed by solvent desorption and gas chromatography no current standard is superseded ISBN 0 580 46134 3 £53.00 members £106.00 non-members EH/2/3 BS EN 14666:2005 Surface active agents. Determination of tetraacetyl ethylene diamine (TAED) content in TAED granules. Gas chromatographic method no current standard is superseded ISBN 0 580 46360 5 £26.00 members £52.00 non-members CII/34 BS EN 14712:2005 Surface active agents. Determination of physical stability in alkaline and acid solutions no current standard is superseded ISBN 0 580 46101 7 £26.00 members £52.00 non-members CII/34 BS EN 14733:2005 Bitumen and bituminous binders. Bituminous emulsions, fluxed and cut-back bitumen factory production control no current standard is superseded ISBN 0 580 46159 9 £32.00 members £64.00 non-members B/510/19 BS EN ISO 17707:2005 Footwear. Test methods for outsoles. Flex resistance no current standard is superseded ISBN 0 580 46424 5 £26.00 members £52.00 non-members TCI/69 BS EN 50131:Alarm systems. Intrusion systems BS EN 50131-5-3:2005 Requirements for interconnections equipment using radio frequency techniques no current standard is superseded ISBN 0 580 46135 1 £46.00 members £92.00 non-members GW/1 BS EN 50370:Electromagnetic compatibility (EMC). Product family standard for machine tools BS EN 50370-1:2005 Emission no current standard is superseded ISBN 0 580 46136 X £32.00 members £64.00 non-members GEL/210/11 BS EN 60401:Terms and nomenclature for cores made of magnetically soft ferrites BS EN 60401-1:2005 Terms used for physical irregularities no current standard is superseded ISBN 0 580 46092 4 £32.00 members £64.00 non-members EPL/51 BS EN 60480:2004 Guidelines for the checking and treatment of sulphur hexafluoride (SF$d6) taken from electrical equipment and specification for its re-use partially supersedes BS 5209:1975 ISBN 0 580 45947 0 £53.00 members £106.00 non-members GEL/10 Page 3 of 69 BS EN 60939:Passive filter units for electromagnetic interference suppression BS EN 60939-2:2005 Sectional specification: passive filter units for which safety tests are appropriate. Test methods and general requirements supersedes BS EN 133200:1999 which remains current ISBN 0 580 46032 0 £60.00 members £120.00 non-members EPL/40 BS EN 61241:Electrical apparatus for use in the presence of combustible dust BS EN 61241-17:2005 Inspection and maintenance of electrical installations in hazardous areas (other than mines) partially supersedes BS EN 50281-1-2:1999, BS 6467-1:1985 and BS 6467-2:1988 ISBN 0 580 46048 7 £46.00 members £92.00 non-members GEL/31/20 BS EN 61243:Live working. Voltage detectors BS EN 61243-1:2005 Capacitive type to be used for voltages exceeding 1 kV a.c supersedes BS EN 61243-1:1998 ISBN 0 580 45943 8 £64.00 members £128.00 non-members PEL/78 BS EN 61249:Materials for printed boards and other interconnecting structures BS EN 61249-2:Reinforced base materials, clad and unclad BS EN 61249-2-1:2005 Phenolic cellulose paper reinforced laminated sheets, economic grade, copper clad no current standard is superseded ISBN 0 580 45936 5 £32.00 members £64.00 non-members EPL/501 BS IMPLEMENTATIONS BS EN 61249-2-22:2005 Modified non-halogenated epoxide woven E-glass laminated sheets of defined flammability (vertical burning test), copper-clad no current standard is superseded ISBN 0 580 45928 4 £46.00 members £92.00 non-members EPL/501 BS EN 61249-2-23:2005 Non-halogenated phenolic cellulose paper reinforced laminated sheets, economic grade, copper-clad no current standard is superseded ISBN 0 580 45927 6 £32.00 members £64.00 non-members EPL/501 BS EN 61290:Optical amplifiers. Test methods BS EN 61290-11:Polarization mode dispersion parameter BS EN 61290-11-2:2005 Poincare$1P sphere analysis method no current standard is superseded ISBN 0 580 46049 5 £32.00 members £64.00 non-members GEL/86/3 BS EN 61300:Fibre optic interconnecting devices and passive components. Basic test and measurement procedures BS EN 61300-2:Tests BS EN 61300-2-44:2005 Flexing of the strain relief of fibre optic devices no current standard is superseded ISBN 0 580 46047 9 £26.00 members £52.00 non-members GEL/86/2 BS EN 61754:Fibre optic connector interfaces BS EN 61754-21:2005 Type SMI connector family for plastic optical fibre no current standard is superseded ISBN 0 580 46043 6 £32.00 members £64.00 non-members GEL/86/2 BS EN 62044:Cores made of soft magnetic materials. Measuring methods BS EN 62044-2:2005 Magnetic properties at low excitation level no current standard is superseded ISBN 0 580 46042 8 £53.00 members £106.00 non-members EPL/51 BS EN 62115:2005 Electric toys. Safety supersedes BS EN 50088:1996 which remains current ISBN 0 580 46091 6 £53.00 members £106.00 non-members CPL/61/21 BS IMPLEMENTATIONS BS ISO 248:2005 Rubber, raw. Determination of volatile-matter content supersedes BS 7164-6.1:1994 ISBN 0 582 46505 5 £32.00 members £64.00 non-members PRI/23 BS ISO 727:Fittings made from unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure BS ISO 727-2:2005 Inch-based series supersedes BS ISO 727-2:2002 ISBN 0 580 46232 3 £26.00 members £52.00 non-members PRI/88/2 Page 4 of 69 BS ISO 1830:2005 Paper, board and pulps. Determination of acid-soluble manganese supersedes BS 4897-4:1983 ISBN 0 580 46444 X £26.00 members £52.00 non-members PAI/11 BS ISO 2108:2005 Information and documentation. International standard book number (ISBN) no current standard is superseded ISBN 0 580 46234 X £46.00 members £92.00 non-members IDT/2/18 BS ISO 3575:2005 Continuous hot-dip zinc-coated carbon steel sheet of commercial and drawing qualities no current standard is superseded ISBN 0 580 46469 5 £32.00 members £64.00 non-members ISE/10 BS ISO 3865:2005 Rubber, vulcanized or thermoplastic. Methods of test for staining in contact with organic material supersedes BS ISO 3865:1997 ISBN 0 580 46389 3 £32.00 members £64.00 non-members PRI/22 BS ISO 4087:2005 Micrographics. Microfilming of newspapers for archival purposes on 35 mm microfilm supersedes BS ISO 4087:1991 ISBN 0 580 46429 6 £32.00 members £64.00 non-members IDT/1/2 BS ISO 4249:Motorcycle tyres and rims (code-designated series) BS ISO 4249-3:2004 Rims no current standard is superseded ISBN 0 580 46210 2 £32.00 members £64.00 non-members AUE/4 BS IMPLEMENTATIONS BS ISO 5168:2005 Measurement of fluid flow. Procedures for the evaluation of uncertainties supersedes BS ISO TR 5168:1998 ISBN 0 580 46279 X £70.00 members £140.00 non-members CPI/30/9 BS ISO 6588:Paper, board and pulps. Determination of pH of aqueous extracts BS ISO 6588-1:2005 Cold extraction partially supersedes BS 2924-1:1983 ISBN 0 580 46438 5 £32.00 members £64.00 non-members PAI/11 BS ISO 7141:2005 Road vehicles. Light alloy wheels. Impact test no current standard is superseded ISBN 0 580 46270 6 £26.00 members £52.00 non-members AUE/4 BS ISO 7341:2005 Banking. Nostro accounts reconciliation supersedes BS ISO 7341:2000 ISBN 0 580 46209 9 £46.00 members £92.00 non-members IST/12 BS ISO 7867:Tyres and rims (metric series) for agricultural tractors and machines BS ISO 7867-1:2005 Tyre designation, dimensions and marking, and tyre/rim coordination supersedes BS AU 50-1.4.5a:1996 ISBN 0 580 46472 5 £46.00 members £92.00 non-members AUE/4 BS ISO 7981:Water quality. Determination of polycyclic aromatic hydrocarbons (PAH) BS ISO 7981-1:2005 Determination of six PAH by high performance thin layer chromatography with fluorescence detection after liquid-liquid extraction no current standard is superseded ISBN 0 580 46410 5 £46.00 members £92.00 non-members EH/3/2 BS ISO 7981-2:2005 Determination of six PAH by high-performance liquid chromatography with fluorescence detection after liquid-liquid extraction no current standard is superseded ISBN 0 580 46411 3 £46.00 members £92.00 non-members EH/3/2 BS ISO 8600:Optics and photonics. Medical endoscopes and endotherapy devices BS ISO 8600-1:2005 General requirements supersedes BS ISO 8600-1:1997 ISBN 0 580 46292 7 £32.00 members £64.00 non-members CPW/172/5 BS ISO 8600-5:2005 Determination of optical resolution of rigid endoscopes with optics no current standard is superseded ISBN 0 580 46432 6 £26.00 members £52.00 non-members CPW/172/5 BS ISO 8600-6:2005 Vocabulary no current standard is superseded ISBN 0 580 46291 9 £26.00 members £52.00 non-members CPW/172/5 BS ISO 13216:Road vehicles. Anchorages in vehicles and attachments to anchorages for child restraint systems Page 5 of 69 BS ISO 13216-2:2004 Top tether anchorages and attachments no current standard is superseded ISBN 0 580 46208 0 £46.00 members £92.00 non-members AUE/7 BS ISO 13899:Steel. Determination of Mo, Nb and W contents in alloyed steel. Inductively coupled plasma atomic emission spectrometric method BS ISO 13899-2:2005 Determination of Nb Content no current standard is superseded ISBN 0 580 46377 X £32.00 members £64.00 non-members ISE/18 BS ISO 14420:2005 Carbonaceous products for the production of aluminium. Baked anodes and shaped carbon products. Determination of the coefficient of linear thermal expansion no current standard is superseded ISBN 0 580 46452 0 £26.00 members £52.00 non-members CII/24 BS ISO 14461:Milk and milk products. Quality control in microbiological laboratories BS ISO 14461-2:2005 Determination of the reliability of colony counts of parallel plates and subsequent dilution steps no current standard is superseded ISBN 0 580 46093 2 £46.00 members £92.00 non-members AW/9 BS ISO 14674:2005 Milk and milk powder. Determination of aflatoxin M$d1 content. Clean-up by immunoaffinity chromatography and determination by thin-layer chromatography no current standard is superseded ISBN 0 580 46228 5 £32.00 members £64.00 non-members AW/5 BS IMPLEMENTATIONS BS ISO 15583:2005 Ships and marine technology. Maritime standards list no current standard is superseded ISBN 0 580 46398 2 £74.00 members £148.00 non-members SME/32/9 BS ISO 15634:2005 Iron ores. Determination of chromium content. Flame atomic absorption spectrometric method partially supersedes BS 7020-16:1993 ISBN 0 580 46216 1 £32.00 members £64.00 non-members ISE/58 BS ISO 16063:Methods for the calibration of vibration and shock transducers BS ISO 16063-22:2005 Shock calibration by comparison to a reference transducer supersedes BS 6955-4:1994 ISBN 0 580 46281 1 £46.00 members £92.00 non-members GME/21/2 BS ISO 16241:2005 Notch tensile test to measure the resistance to slow crack growth of polyethylene materials for pipe and fitting products (PENT) no current standard is superseded ISBN 0 580 46143 2 £32.00 members £64.00 non-members PRI/88/4 BS ISO 16881:Cranes. Design calculation for rail wheels and associated trolley track supporting structure BS ISO 16881-1:2005 General no current standard is superseded ISBN 0 580 46470 9 £32.00 members £64.00 non-members MHE/3/3 BS ISO 17247:2005 Coal. Ultimate analysis no current standard is superseded ISBN 0 580 46089 4 £26.00 members £52.00 non-members PTI/16 BS ISO 17356:Road vehicles. Open interface for embedded automotive applications BS ISO 17356-2:2005 OSEK/VDX specifications for binding OS, COM and NM no current standard is superseded ISBN 0 580 46477 6 £26.00 members £52.00 non-members AUE/16 BS ISO/IEC 18033:Information technology. Security techniques. Encryption algorithms BS ISO/IEC 18033-1:2005 General no current standard is superseded ISBN 0 580 46144 0 £32.00 members £64.00 non-members IST/33 BS ISO 18852:2005 Rubber compounding ingredients. Determination of multipoint nitrogen surface area (NSA) and statistical thickness surface area (STSA) no current standard is superseded ISBN 0 580 46233 1 £32.00 members £64.00 non-members PRI/50 BS ISO 19109:2005 Geographic information. Rules for application schema no current standard is superseded ISBN 0 580 46379 6 £70.00 members £140.00 non-members IST/36 Page 6 of 69 BS ISO 24237:2005 Surface chemical analysis. X-ray photoelectron spectroscopy. Repeatability and constancy of intensity scale no current standard is superseded ISBN 0 580 46280 3 £32.00 members £64.00 non-members CII/60 KIT 147 Graphical symbols kit no current standard is superseded ISBN 0 580 33404 X £206.00 members £412.00 non-members VAT is applicable to this item. Special offer. Includes BS 5499 Parts 1 to 6 and Part 11 and EP 250 (Safety signs and symbols CD-ROM). KIT 148 Surface texture standards kit no current standard is superseded ISBN 0 580 33405 8 £395.00 members £790.00 non-members Special offer. Includes BS EN ISO 1302, BS EN ISO 3274, BS EN ISO 4287, BS EN ISO 4288, BS EN ISO 8785, BS ISO 10135, BS EN ISO 11562, BS EN ISO 12085, BS EN ISO 13565 Parts 1 to 3, BS EN ISO 14253-1, BS EN ISO 14660-1 and BS EN ISO 81714-1. KIT 162 Structural bearings kit no current standard is superseded ISBN 0 580 33419 8 £258.00 members £516.00 non-members Special offer. Includes BS EN 1337 Parts 1 & 2, 4, 6 & 7, and 9 to 11. KIT 163 Concrete standards kit no current standard is superseded ISBN 0 580 33420 1 £190.00 members £380.00 non-members Special offer. Includes BS 8500 Parts 1 & 2, BS EN 206-1 and BIP 2001. KIT 164 Testing concrete in structures kit no current standard is superseded ISBN 0 580 33421 X £67.00 members £134.00 non-members Special offer. Includes BS EN 12504 Parts 1, 2 & 4. KIT 165 Concrete paving requirements & test methods kit no current standard is superseded ISBN 0 580 33422 8 £303.00 members £606.00 non-members Special offer. Includes BS 6717, BS 7263-1, BS EN 1340, BS EN 1338, BS EN 1339, BS EN 12629-2, and BS EN 13863 Parts 1 & 2. KIT 166 Concrete paving kit no current standard is superseded ISBN 0 580 33424 4 £212.00 members £424.00 non-members Special offer. Includes BS 7533 Parts 1 to 4, 6 to 8, 10 and 11. KIT 167 Hot rolled products of structural steels kit no current standard is superseded ISBN 0 580 33418 X £232.00 members £464.00 non-members Special offer. Includes BS EN 10025 Parts 1 to 6. KIT 168 CE marking for insulating glass units kit no current standard is superseded ISBN 0 580 33424 4 £615.95 members £806.00 non-members Special offer. Includes BS EN 1279 Parts 1 to 4 and Part 6, and a manufacturer's toolkit (BIP 3001) on CD-ROM. KIT 169 Insulating glass units kit no current standard is superseded ISBN 0 580 33425 2 £191.00 members £382.00 non-members Special offer. Includes BS EN 1279 Parts 1 to 4 and Part 6. IT AND INFORMATION MANAGEMENT PUBLICATIONS AND PRODUCTS BIP 0018:2005 Simplifying the implementation of MPEG CD-ROM no current standard is superseded ISBN 0 580 46110 6 £35.00 members £35.00 non-members VAT is applicable to this item. SPECIALIST BOOKS FROM BSI BIP 2073:2005 Quality patient care in hospitals no current standard is superseded ISBN 0 580 45646 3 £30.00 members £30.00 non-members ELECTRONIC PRODUCTS BIP 0022:2005 RA2 Art of risk CD-ROM no current standard is superseded £977.00 members £977.00 non-members VAT is applicable to this item. AMENDMENTS TO BRITISH STANDARDS BS 750:1984 Specification for underground fire hydrants and surface box frames and covers CORRIGENDUM 1 AMD 15667 Updated standard: Please order by the reference: BS 750:1984 £46.00 members £92.00 non-members FSH/17 Also incorporates Amendment 1, 2 and 3. BS 2000:Methods of test for petroleum and its products KITS, SETS, PACKS AND SERIES KIT 146 Graphical symbols kit no current standard is superseded ISBN 0 580 33403 1 £149.00 members £298.00 non-members Special offer. Includes BS 5499 Parts 1 to 6 and Part 11. AMENDMENTS TO BRITISH STANDARDS Page 7 of 69 BS 2000-239:Determination of the extreme-pressure and anti-wear properties of fluids. Four ball method (European conditions) See BS EN ISO 20623. BS 6312:Connectors for analogue telecommunication interfaces BS 6312-2:Sockets for use with plugs specified in BS 6312:Part 1 BS 6312-2.2:1997 Particular requirements for fixed socket-outlets used in permanent wiring installations AMENDMENT 1 AMD 15632 Updated standard: Please order by the reference: BS 6312-2.2:1997 £32.00 members £64.00 non-members TCT/2 BS 7499:2002 Static site guarding and mobile patrol services. Code of practice AMENDMENT 1 AMD 15926 Updated standard: Please order by the reference: BS 7499:2002 £46.00 members £92.00 non-members GW/3, GW/3/-/3 BS 8418:2003 Installation and remote monitoring of detector activated CCTV systems. Code of practice AMENDMENT 1 AMD 15833 Updated standard: Please order by the reference: BS 8418:2003 £32.00 members £64.00 non-members GW/1, GW/1/10 BS EN ISO 20623:2003 (BS 2000-239:2004) Petroleum and related products. Determination of the extreme-pressure and anti-wear properties of fluids. Four ball method (European conditions) AMENDMENT 1 AMD 15634 Updated standard: Please order by the reference: BS EN ISO 20623:2003 £16.65 members £22.20 non-members PTI/13 Also incorporates Corrigendum 1. BS EN 60335:Specification for safety of household and similar electrical appliances BS EN 60335-2:Particular requirements BS EN 60335-2-29:2004 Battery chargers AMENDMENT 1 AMD 15769 Updated standard: Please order by the reference: BS EN 60335-2-29:2004 £32.00 members £64.00 non-members CPL/61, CPL/61/01 Also incorporates Corrigendum 1. BS EN 26:1998 Gas-fired instantaneous water heaters for the production of domestic hot water, fitted with atmospheric burners AMENDMENT 2 Updated standard: Please order by the reference: BS EN 26:1998 £74.00 members £148.00 non-members GSE/34 Also incorporates Amendment 1. SPECIAL ANNOUNCEMENTS NEW BT/TF Services of real estate agents The Technical Board (BT) of the European Standardisation Agency (CEN) has proposed the establishment of a Technical Board/Task Force (BT/TF) to react to an application from the Austrian National Standards Body (ON). This application sets out to develop a Contact: Ray Kerrigan Email: [email protected] NONE BS EN 1949:2002/A1 Specification for the installation of LPG systems for habitation purposes in leisure accommodation vehicles and in other vehicles No Draft for Public Comment was issued for this standard, which was amended by CEN/TC 181. Further information may be obtained from the contact point (below). Contact: Committee Service Centre Email: [email protected] GSE/24 BS EN 50144:Safety of hand-held electric motor operated tools UPDATED BRITISH STANDARDS BS 6037:Code of practice for the planning, design, installation and use of permanently installed access equipment BS 6037-1:2003 Suspended access equipment AMENDMENT 1 Updated standard: Please order by the reference: BS 6037-1:2003 £46.00 members £92.00 non-members B/514, B/514/39 SPECIAL ANNOUNCEMENTS Page 8 of 69 BS EN 50144-1:1999 General requirements This standard, which was withdrawn on 1 July 2005 in line with the national foreword to the superseding publication BS EN 60745-1:2003, is now to be re-instated. Subsequent to publication of BS EN 60745-1 in May 2003 it was realised that a number of s Contact: Geraldine Salt Email: [email protected] CPL/61/6 prEN ISO 12625:Tissue paper and tissue products prEN ISO 12625-7 Determination of optical properties This document has been issued for enquiry and is being reviewed by committee PAI/11. Copies are available upon request from the committee secretary (below). Contact: Sue Barden Email: [email protected] PAI/11 EN 13136:2001/A1 Refrigerating systems and heat pumps. Pressure relief devices and their associated piping. Method for calculation The European document has recently been published and will shortly be made available in the UK as an amendment to BS EN 13136:2001 . Contact: Nyomee Kyaw Email: [email protected] RHE/18 prCEN/TS 14383:Prevention of crime. Urban planning and design prCEN/TS 14383-4 Shops and offices This final draft has recently been received for FV (Formal Vote) and circulated to committee B/209/10. Further information is available from the committee secretary (below). Contact: Ranjit Bhambra Email: [email protected] B/209/10 prCEN/TR 15352 Bitumen and bituminous binders. Development of performance-related specifications This final draft has recently been received for FV (Formal Vote) and circulated to committee B/510/19. Further information is available from the committee secretary (below). Contact: Ranjit Bhambra Email: [email protected] B/510/19 ISO/FDIS 8262:Milk products and milk-based foods. Determination of fat content by the Weibull-Berntrop gravimetric method (reference method) ISO/FDIS 8262-3 Special cases This standard has been circulated to ISO members as a Final Draft International Standard (FDIS) by ISO/TC 34/SC 5. It incorporates minor revisions to the earlier version of the International standard. It has not been circulated as a Draft for Publlic Com Contact: Committee Service Centre Email: [email protected] AW/5 BS 873-2:1984 Specification for miscellaneous signs B/509 BS 873-3:1980 Specification for internally illuminated bollards B/509 BS 873-4:1987 Specification for road studs B/509 BS 873-7:1984 Specification for posts and fittings B/509 BS 1191:Specification for gypsum building plasters BS 1191-1:1973 Excluding premixed lightweight plasters B/544 BS 1191-2:1973 Premixed lightweight plasters B/544 BS 1230:Gypsum plasterboard BS 1230-1:1985 Specification for plasterboard excluding materials submitted to secondary operations B/544 BS 1306:1975 Specification for copper and copper alloy pressure piping systems PVE/10 BS 1369:Steel lathing for internal plastering and external rendering BS 1369-1:1987 Specification for expanded metal and ribbed lathing B/544 BS 1467:1972 Specification for folders and files FW/0 BS 1560:Circular flanges for pipes, valves and fittings (class designated) BRITISH STANDARDS PROPOSED FOR CONFIRMATION BS 499:Welding terms and symbols BS 499-2C:1999 European arc welding symbols in chart form WEE/1 BS 500:2000 Steel sleepers RAE/2/-/1 BS 873:Road traffic signs and internally illuminated bollards BS 873-1:1983 Methods of test B/509 BRITISH STANDARDS PROPOSED FOR CONFIRMATION Page 9 of 69 BS 1560-3:Steel, cast iron and copper alloy flanges BS 1560-3.2:1989 Specification for cast iron flanges PSE/15 BS 2737:1956 Terminology of internal defects in castings as revealed by radiography WEE/46 BS 3143:Road danger lamps BS 3143-2:1990 Specification for low-intensity battery-operated lamps B/509 BS 3143-4:1985 Specification for high intensity battery operated beacons B/509 BS 3262:Hot-applied thermoplastic road marking materials BS 3262-3:1989 Specification for application of material to road surfaces B/509 BS 3273:1960 Specification for distant indicating thermometers for ships' refrigerated cargo spaces SME/32 BS 3293:1960 Specification for carbon steel pipe flanges (over 24 inches nominal size) for the petroleum industry PSE/15 BS 3934:Mechanical standardization of semiconductor devices BS 3934-10:1992 Schedule of UK national drawings giving dimensions EPL/47 BS 4022:1970 Specification for prefabricated gypsum wallboard panels B/544 BS 4089:1999 Specification for metallic hose assemblies for liquid petroleum gases and liquefied natural gases PSE/12 BS 4263:1967 Specification for the marking of hatchway beams SME/32 BS 4507:1969 Specification for grease gun cartridges (composite type) GME/24 BS 4515:Specification for welding of steel pipelines on land and offshore BS 4515-2:1999 Duplex stainless steel pipelines WEE/21/7 BS 5077:1974 Specification for grease guns (hand-operated lever type) for use with cartridges complying with BS 4507 GME/24 BS 5262:1991 Code of practice for external renderings B/544 BS 5492:1990 Code of practice for internal plastering B/544 BS 5873:Educational furniture BS 5873-1:1980 Specification for functional dimensions, identification and finish of chairs and tables for educational institutions FW/0 BS 5873-2:1991 Specification for strength and stability of chairs for educational institutions FW/0 BS 5873-3:1985 Specification for strength and stability of tables for educational institutions FW/0 BS 5873-4:1998 Specification for strength and stability of storage furniture for educational institutions FW/0 BS 5873-5:1998 Specification for security of fixed secure storage furniture for educational institutions FW/0 BS 6129:Code of practice for the selection and application of bellows expansion joints for use in pressure systems BS 6129-1:1981 Metallic bellows expansion joints PSE/14 BS 6130:Hose and hose assemblies for asphalt and bitumen BS 6130-1:1993 Specification for flexible metallic hose and hose assemblies PSE/12 BS 6222:Domestic kitchen equipment BS 6222-3:1999 Performance requirements for durability of surface finish and adhesion of surfacing and edging materials. Specification FW/0 BS 6325:1982 Glossary of terms relating to black tea AW/8 BS 6452:Beads for internal plastering and dry lining BS 6452-1:1984 Specification for galvanized steel beads B/544 BS 6571:Vehicle parking control equipment BS 6571-1:1989 Specification for coin operated clockwork parking meters B/509 Page 10 of 69 BRITISH STANDARDS PROPOSED FOR CONFIRMATION BS 6571-2:1989 Specification for electrically powered parking meters B/509 BS 6571-4:1989 Specification for barrier type parking control equipment B/509 BS 6571-6:1996 Specification for pay-on-foot parking control equipment B/509/20 BS 6571-7:1997 Specification for parking discs B/509/20 BS 6571-8:1997 Specification for pre-purchased parking vouchers B/509/20 BS 6779:Highway parapets for bridges and other structures BS 6779-1:1998 Specification for vehicle containment parapets of metal construction B/509/1 BS 6779-2:1991 Specification for vehicle containment parapets of concrete construction B/509 BS 7364:1990 Specification for galvanized steel studs and channels for stud and sheet partitions and linings using screw fixed gypsum wallboards B/544 BS 7449:1991 Specification for inclusion of glass in the construction of furniture, other than tables or trolleys, including cabinets, shelving systems and wall hung or free standing mirrors FW/0 BS 7777:Flat-bottomed, vertical, cylindrical storage tanks for low temperature service BS 7777-1:1993 Guide to the general provisions applying for design, construction, installation and operation PVE/15 BS 7777-2:1993 Specification for the design and construction of single, double and full containment metal tanks for the storage of liquefied gas at temperatures down to -165$0DC PVE/15 BS 7777-3:1993 Recommendations for the design and construction of prestressed and reinforced concrete tanks and tank foundations, and for the design and installation of tank insulation, tank liners and tank coatings PVE/15 BS 7777-4:1993 Specification for the design and construction of single containment tanks for the storage of liquid oxygen, liquid nitrogen and liquid argon PVE/15 BS 7945:1999 Non-domestic furniture. Seating. Determination of stability FW/0 BS 7962:2000 Black materials for masking existing road markings. Specification B/509/2 BS 8212:1995 Code of practice for dry lining and partitioning using gypsum plasterboard B/544/3 BS 9300 C199-276:1971 Detail specification for silicon voltage-regulator diodes EPL/47 BS 9300 C377-378:1971 Detail specifications for silicon coaxial mixer diodes EPL/47 BS 9300 C379-388:1971 Detail specifications for silicon stud mounted, power rectifier diodes EPL/47 BS 9300 C476:1973 Detail specification for silicon avalanche rectifier diode EPL/47 BS 9300 C534:1971 Detail specification for silicon coaxial resistive switching diode EPL/47 BS 9300 C582-584:1971 Detail specifications for reverse blocking triode thyristors EPL/47 BS 9300 C599:1971 Detail specification for silicon microwave switching diode, rod mounted EPL/47 BS 9300 C667-668:1971 Detail specification for silicon avalanche rectifier diodes EPL/47 BS 9300 C678-721:1971 Detail specification for silicon voltage regulator diodes EPL/47 BS 9300 C762:1971 Detail specification for mixer diodes for use at X-band frequencies EPL/47 BS 9300 C771-772:1971 Detail specification for coaxial mixer diodes EPL/47 BS 9300 C776-777:1971 Detail specification for germanium coaxial mixer diodes EPL/47 BS 9300 C778:1971 Detail specification for a matched pair of germanium coaxial mixer diodes EPL/47 BS 9300 C780-831:1971 Detail specification for silicon voltage regulator diodes EPL/47 Page 11 of 69 BRITISH STANDARDS PROPOSED FOR CONFIRMATION BS 9300 C841-849:1971 Detail specification for silicon voltage regulator diodes EPL/47 BS 9301 N002:1971 Detail specification for general purpose silicon signal diodes. 150 mA, 150 V, hermetically sealed, glass encapsulation. General application category Q EPL/47 BS 9305 N001:1972 Detail specification for silicon voltage regulator diodes. 1.5 W, 3.3 to 33 V (5%), hermetically sealed. General application category Q EPL/47 BS 9305 N041:1972 Detail specification for silicon voltage regulator diodes. 400 mW, 2.7 to 33 V (5%), hermetically sealed, glass encapsulation. General application category Q EPL/47 BS 9305 N042:1972 Detail specification for silicon voltage regulator diodes. 1.5 W, 6.8 to 200 V (5%), hermetically sealed. General application category C EPL/47 BS 9305 N044:1974 Detail specification for silicon voltage regulator diodes. 1.0 W, 3.3 to 33 V (5%), hermetically sealed. Full assessment level EPL/47 BS 9364 N007 and N009:1978 Detail specification for low power silicon n-p-n switching transistors. 20 V, planar epitaxial, ambient rated, hermetic encapsulation. Full plus additional assessment level EPL/47 BS 9364 N008 and N010:1978 Detail specification for low power silicon n-p-n switching transistors. 20 V, planar epitaxial, ambient rated, hermetic encapsulation (long lead version). Full plus additional assessment level EPL/47 BS 9364 N011:1978 Detail specification for low power silicon p-n-p switching transistors. 65 V, planar epitaxial, ambient rated, hermetic encapsulation. Full plus additional assessment level EPL/47 BS 9364 N012:1978 Detail specification for low power silicon p-n-p switching transistors. 65 V, planar epitaxial, ambient rated, hermetic encapsulation (long lead version). Full plus additional assessment level EPL/47 BS 9364 N013:1979 Detail specification for low power silicon p-n-p switching transistors. 25 V, planar epitaxial, ambient rated, hermetic encapsulation. Full plus additional assessment level EPL/47 BS 9364 N016:1979 Detail specification for low power silicon n-p-n switching transistors. 65 V, planar epitaxial, ambient rated, hermetic encapsulation. Full plus additional assessment level EPL/47 BS 9364 N017:1979 Detail specification for low power silicon n-p-n switching transistors. 65 V, planar epitaxial, ambient rated, hermetic encapsulation (long lead version). Full plus additional assessment level EPL/47 BS 9430:1978 Rules for the preparation of detail specifications for integrated circuits of assessed quality: voltage regulators. Full assessment level EPL/47 BS 9490:1975 Rules for the preparation of detail specifications for digital integrated circuits of assessed quality. Full assessment level EPL/47 BS 9493:1981 Rules for the preparation of detail specifications for integrated circuits of assessed quality which perform mixed digital and/or analogue functions EPL/47 BS ISO 4708:2000 Composition cork. Gasket material. Test methods PRI/81 BS ISO 4709:2000 Composition cork. Gasket material. Classification system, requirements, sampling, packing and marking PRI/81 BS ISO 4710:2000 Cork. Cylindrical stoppers for sparkling wines and gasified wines. Characteristics PRI/81 BS ISO 4714:2000 Composition cork. Specifications, sampling, packaging and marking PRI/81 BS ISO 7322:2000 Composition cork. Test methods PRI/81 PD 6430/1:1970 Extract (appendices A and B) from PD 6430: 'The adoption of the metric system in the marine industry: report, basic programme and guide. Units of the SI, their application and use in the marine industry' SME/32 PD 6460:1971 Collected amendments to the CV7000 specifications for semiconductors adopted as British Standards (9300C series) EPL/47 PD 7777:2000 Alternative steel selection and its effect on design and testing of tanks to BS 7777 PVE/15 PD ES 59008:Data requirements for semiconductor die BRITISH STANDARDS PROPOSED FOR CONFIRMATION Page 12 of 69 PD ES 59008-1:2000 General requirements EPL/47 PD ES 59008-2:1999 Vocabulary EPL/47 PD ES 59008-3:1999 Mechanical, material and connectivity requirements EPL/47 PD ES 59008-4:Specific requirements and recommendations PD ES 59008-4-3:2000 Thermal EPL/47 PD ES 59008-4-4:2000 Electrical simulation EPL/47 PD ES 59008-6:Exchange data formats and data dictionary PD ES 59008-6-1:1999 Data exchange. DDX file format EPL/47 BS MA 6:1970 Specification for internal doors and frames SME/32 BS MA 7:1983 Specification for manholes with bolted covers SME/32 BS MA 9:1970 Flanges, bolting and gaskets for exhaust gas, piping for diesel engines and boiler uptakes SME/32 BS MA 10:1971 Specification for oval eyeplates SME/32 BS MA 11:1971 Specification for horncleats SME/32 BS MA 12:Specification for welded steel bollards BS MA 12-1:1983 Vertical type SME/32 BS MA 12-2:1983 Cruciform type SME/32 BS MA 13:1972 Recommendations for the co-ordination of dimensions in shipbuilding: glossary of terms SME/32 BS MA 14:1972 Recommendations for the co-ordination of dimensions in shipbuilding: co-ordinating sizes for components and assemblies SME/32 BS MA 17:1972 Specification for derrick boom clamp SME/32 BS MA 18:1973 Specification for salt water piping systems in ships SME/32 BS MA 19:1973 Specification for panama-type fairleads SME/32 BS MA 20:1973 Specification for presentation of ships' cargo gear particulars SME/32 BS MA 21:1973 Specification for deck-end roller fairleads SME/32 BS MA 22:1973 Specification for cast roller fairleads SME/32 BS MA 23:1973 Specification for multi-angle roller fairleads SME/32 BS MA 25:1973 Specification for ships' windows SME/32 BS MA 26:1973 Specification for suction strainers SME/32 BS MA 27:1974 Specification for sight-flow indicators for tank overflow systems SME/32 BS MA 30:1973 Glossary of terms and graphical symbols for ships' deck machinery SME/32 BS MA 31:1973 Specification for ships' deck machinery. Cargo winches SME/32 BS MA 33:1973 Specification for ships' deck machinery. Warping winches SME/32 BS MA 34:1973 Specification for ships' deck machinery. Capstans SME/32 BS MA 35:1975 Specification for ships' deck machinery. Windlasses SME/32 BS MA 36:1974 Specification for ships' deck machinery. Topping winches SME/32 BS MA 37:1973 Specification for external doors (wood) for ships SME/32 BS MA 39:Specification for ships' ladders BS MA 39-1:1973 Ladders, steel vertical SME/32 BS MA 39-2:1973 Ladders, steel sloping SME/32 BS MA 39-3:1973 Ladders, steel dog-step SME/32 BS MA 40:Specification for marine guardrails, stanchions, etc BRITISH STANDARDS PROPOSED FOR CONFIRMATION Page 13 of 69 BS MA 40-1:1975 Guardrails for merchant ships (excluding passenger ships) SME/32 BS MA 40-2:1975 Gates and portable guardrail sections for merchant ships (excluding passenger ships) SME/32 BS MA 40-3:1975 Storm rails (exterior) SME/32 BS MA 42:1975 Specification for ships' awnings and supports SME/32 BS MA 44:1974 Recommendations for the co-ordination of dimensions in shipbuilding: principles of dimensional co-ordination SME/32 BS MA 45:1974 Recommendations for the co-ordination of dimensions in shipbuilding: controlling dimensions SME/32 BS MA 46:1973 Specification for cast iron mudboxes SME/32 BS MA 49:1986 Summary and application of carbon steel tubes for marine pipework systems SME/32 BS MA 52:1974 Specification for ships' deck machinery. Accommodation ladder winches SME/32 BS MA 53:1975 Specification for ships' deck machinery. Towing winches for deep sea use SME/32 BS MA 55:1975 Specification for ships' deck machinery. Lifeboat winches SME/32 BS MA 56:1974 Specification for ships' deck machinery. Anchor cable stoppers SME/32 BS MA 59:1974 Specification for sea tubes SME/32 BS MA 60:1986 Summary and application of copper and copper alloy tubes for ships' pipework systems SME/32 BS MA 61:1974 Specification for bilge drain and suction hats SME/32 BS MA 62:1974 Specification for weed grids for sea inlets SME/32 BS MA 69:1976 Specification. Ventilator heads SME/32 BS MA 70:Specification for dimensions of anchor chain cables BS MA 70-1:1975 Stud-link anchor chain cables SME/32 BS MA 71:1977 Recommendations for the co-ordination of dimensions in shipbuilding: co-ordinating spaces for internal subdivision SME/32 BS MA 72:1976 Recommendations for the co-ordination of dimensions in shipbuilding: co-ordinating spaces for furniture SME/32 BS MA 73:1976 Recommendations for the co-ordination of dimensions in shipbuilding: co-ordinating sizes for fixtures, fittings and equipment SME/32 BS MA 74:Tapers and other outboard details of propeller shafts BS MA 74-2:1981 Specification for shafts of diameter greater than 160 mm up to 1000 mm SME/32 BS MA 75:Specification for bulkhead pieces and tank pads BS MA 75-1:1985 Bulkhead pieces of fabricated steel or copper alloy and steel pad pieces SME/32 BS MA 75-2:1978 Bulkhead pieces of ductile iron (spheroidal graphite iron) SME/32 BS MA 77:1976 Recommendations for the co-ordination of dimensions in shipbuilding: co-ordinating sizes for services SME/32 BS MA 78:1978 Specification for aluminium shore gangways SME/32 BS MA 79:1978 Specification for jib cranes: ship mounted type SME/32 BS MA 93:1981 Code of practice for structural safety of deck machinery installation SME/32 BS MA 94:1981 Specification for thermal insulation for marine piping systems SME/32 BRITISH STANDARDS REVIEWED AND CONFIRMED BS 61:1969 Specification for threads for light gauge copper tubes and fittings NFE/34 BS 90:1975 Specification for direct-acting electrical recording instruments and their accessories PEL/85 Page 14 of 69 BRITISH STANDARDS REVIEWED AND CONFIRMED BS 411:1969 Specification for circular saws for woodworking and their attachment MTE/20 BS 448:Dimensions of electronic tubes and valves BS 448-2:1981 Specification for dimensions of United Kingdom electronic tubes EPL/39 BS 459:1988 Specification for matchboarded wooden door leaves for external use B/538 BS 787:Specification for mining type flameproof gate-end boxes BS 787-1:1969 Gate-end boxes for direct-on-line motor starting (for use on 3-phase a.c. circuits up to 650 V) MRE/3 BS 787-2:1968 Gate-end boxes with air-break circuit-breakers (for use on 3-phase a.c. circuits up to 650 volts) MRE/3 BS 787-3:1971 Gate-end boxes with lighting transformers MRE/3 BS 787-4:1972 Gate-end boxes for drilling machines (for use on 3-phase a.c. circuits up to 650 V) MRE/3 BS 853:Specification for vessels for use in heating systems BS 853-2:1996 Tubular heat exchangers and storage vessels for building and industrial services RHE/12 BS 1545:1990 Specification for liquid toilet soap CII/34 BS 1552:1995 Specification for open bottomed taper plug valves for 1st, 2nd and 3rd family gases up to 200 mbar GSE/22 BS 1728:Methods for the analysis of aluminium and aluminium alloys BS 1728-1:1951 Determination of copper NFE/35 BS 1728-5:1953 Determination of copper (absorptiometric method) NFE/35 BS 1728-6:1955 Determination of iron (volumetric: titanous chloride method) NFE/35 BS 1728-8:1957 Determination of iron (absorptiometric 1:10-phenanthroline method) NFE/35 BS 1728-9:1957 Determination of manganese (volumetric: arsenite/nitrite method) NFE/35 BS 1728-10:1957 Determination of manganese (absorptiometric method) NFE/35 BS 1728-11:1960 Determination of silicon (perchloric acid method) NFE/35 BS 1728-12:1961 Determination of silicon (absorptiometric molybdenum blue method) NFE/35 BS 1728-14:1965 Determination of nickel (gravimetric method) NFE/35 BS 1728-15:1966 Determination of nickel (photometric method) NFE/35 BS 1728-16:1968 Determination of chromium (photometric method) NFE/35 BS 1728-17:1968 Determination of chromium (volumetric method) NFE/35 BS 1728-18:1970 Determination of zinc (ion-exchange-volumetric EDTA or polarographic method) NFE/35 BS 1728-19:1971 Determination of magnesium (atomic absorption method) NFE/35 BS 1728-20:1971 Determination of lead (atomic absorption method) NFE/35 BS 1728-21:1973 Zinc (atomic absorption method) NFE/35 BS 1728-22:1972 Determination of magnesium (volumetric CDTA method) NFE/35 BS 1728-23:1976 Copper (atomic absorption method) NFE/35 BS 1728-24:1976 Nickel (atomic absorption method) NFE/35 BS 1911:1990 Specification for hard soap CII/34 BS 1912:1990 Specification for soap flakes CII/34 BS 1913:1990 Specification for soft soap CII/34 BS 1914:1990 Specification for toilet soap CII/34 BS 1919:Hacksaw blades Page 15 of 69 BRITISH STANDARDS REVIEWED AND CONFIRMED BS 1919-1:1993 Specification for hand and machine hacksaw blades MTE/20 BS 1919-2:1995 Specification for cutting performance MTE/20 BS 2011:Environmental testing BS 2011-2.2:Guidance BS 2011-2.2Kd:1984 Test Kd. Guidance on test Kd: hydrogen sulphide test for contacts and connections GEL/104 BS 2011-2.2Z/AFc and Z/BFc:1986 Tests Z/AFc and Z/BFc. Guidance on combined temperature (cold and dry heat) and vibration (sinusoidal) tests GEL/50 BS 2049:1985 Specification for paraffin lighting appliances for domestic use CW/31 BS 2857:1976 Specification for nickel-iron transformer and choke laminations EPL/51 BS 3101:1986 Specification for control and interlock circuits primarily associated with flameproof restrained plugs and sockets for use in coal mines MRE/3 BS 3138:1992 Glossary of terms used in management services MS/1 BS 3300:1985 Specification for paraffin unflued space heating and cooking appliances for domestic use CW/31 BS 3338:Methods for the sampling and analysis of tin and tin alloys BS 3338-2:1961 Method for the determination of tin in ingot tin (aluminium reduction method) NFE/27 BS 3338-3:1961 Method for the determination of antimony in ingot tin (photometric method) NFE/27 BS 3338-4:1961 Method for the determination of copper in ingot tin and tin-lead solders (photometric method) NFE/27 BS 3338-5:1961 Method for the determination of lead in ingot tin and tin-antimony solders (photometric method) NFE/27 BS 3338-6:1961 Method for the determination of copper in high purity ingot tin (photometric method) NFE/27 BS 3338-7:1961 Method for the determination of silver in solders (volumetric: ammonium thiocyanate method) NFE/27 BS 3338-8:1961 Method for the determination of bismuth in ingot tin, tin-lead solders and white metal bearing alloys (photometric method) NFE/27 BS 3338-9:1965 Method for the determination of arsenic in ingot tin, solders and white metal bearing alloys (photometric method) NFE/27 BS 3338-10:1961 Method for the determination of iron in ingot tin, tin-lead solders and white metal bearing alloys (photometric method) NFE/27 BS 3338-11:1961 Method for the determination of tin in solders (nickel coil reduction method) NFE/27 BS 3338-13:1965 Method for the determination of antimony in solders and white metal bearing alloys (volumetric: potassium bromate method) NFE/27 BS 3338-14:1965 Method for the sampling of white metal bearing alloy ingots NFE/27 BS 3338-15:1965 Method for the determination of copper and lead in white metal bearing alloys (electrodeposition method) NFE/27 BS 3338-16:1965 Method for the determination of tin in white metal bearing alloys (nickel coil reduction method) NFE/27 BS 3338-17:1965 Method for the determination of cadmium in solders and white metal bearing alloys (photometric method) NFE/27 BS 3338-18:1966 Method for the determination of aluminium in solders and white metal bearing alloys (photometric method) NFE/27 BS 3338-19:1966 Method for the determination of zinc in solders and white metal bearing alloys (photometric method) NFE/27 BS 3338-20:1970 Method for the determination of nickel in capping metal (photometric method) NFE/27 BS 3338-21:1983 Determination of high cadmium content of soft solders NFE/27 BS 3673:Specification for spring retaining rings BRITISH STANDARDS REVIEWED AND CONFIRMED Page 16 of 69 BS 3673-2:1965 Carbon steel E clips FME/18 BS 3673-3:1968 Carbon steel C clips FME/18 BS 3673-4:1977 Carbon steel circlips: metric series FME/18 BS 3693:1992 Recommendations for design of scales and indexes on analogue indicating instruments PEL/85 BS 3762:Analysis of formulated detergents BS 3762-3:Quantitative test methods BS 3762-3.12:1985 Method for determination of ammonia content CII/34 BS 3762-3.14:1985 Method for determination of carbonate content CII/34 BS 3762-3.15:1985 Method for estimation of carboxymethylcellulose content CII/34 BS 3762-3.16:1985 Method for determination of chloride content CII/34 BS 3877:1991 Specification for metal cutting bandsaw blades MTE/20 BS 3905:1995 Specification for 3.8/6.6 kV, 300 A bolted flameproof cable couplers and adaptors, for use in coal mines MRE/3 BS 3907:Methods for the analysis of magnesium and magnesium alloys BS 3907-1:1965 Determination of aluminium in magnesium alloys (gravimetric method) NFE/35 BS 3907-2:1966 Determination of iron in magnesium and magnesium alloys (photometric - 1:10-phenanthroline method) NFE/35 BS 3907-3:1966 Determination of copper in magnesium and magnesium alloys (photometric method) NFE/35 BS 3907-4:1966 Determination of manganese in magnesium and magnesium alloys (photometric-periodate method) NFE/35 BS 3907-5:1966 Determination of manganese in magnesium and magnesium alloys (photometric-periodate method) (low contents) NFE/35 BS 3907-6:1969 Determination of zirconium in magnesium and magnesium alloys (photometric method) NFE/35 BS 3907-7:1969 Determination of nickel in magnesium alloys (photometric method) NFE/35 BS 3907-8:1970 Determination of total rare earths in magnesium alloys (gravimetric method) NFE/35 BS 3907-9:1969 Determination of zinc in magnesium alloys (ion-exchange-volumetric EDTA method) NFE/35 BS 3907-10:1969 Determination of manganese in magnesium alloys containing zirconium, rare earths, thorium and/or silver (photometric method) NFE/35 BS 3907-11:1970 Determination of silicon in magnesium and magnesium alloys (photometric method) NFE/35 BS 3907-12:1971 Determination of aluminium in magnesium and magnesium alloys (photometric method) NFE/35 BS 3907-13:1972 Determination of tin in magnesium and magnesium alloys (photometric method) NFE/35 BS 3907-15:1976 Determination of lead in magnesium and magnesium alloys (atomic absorption method) NFE/35 BS 4023:1975 Specification for flexible cellular PVC sheeting PRI/71 BS 4078:Powder actuated fixing systems BS 4078-1:1987 Code of practice for safe use MTE/21 BS 4078-2:1989 Specification for tools MTE/21 BS 4105:1990 Specification for liquid carbon dioxide, industrial CII/19 BS 4319:Methods of measurement of the electrical properties of electronic tubes and valves (excluding microwave devices) BS 4319-1:1968 Essential conditions for measuring equivalent input and output admittances EPL/39 BS 4393:1991 Specification for solderable tin or tin-lead coated wires for component terminations NFE/27 Page 17 of 69 BRITISH STANDARDS REVIEWED AND CONFIRMED BS 4405:1990 Specification for liquid soap CII/34 BS 4411:1969 Specification for woodcutting bandsaw blades MTE/20 BS 4443:Methods of test for flexible cellular materials BS 4443-4:1989 Method 10. Determination of solvent swelling PRI/24 BS 4462:1969 Guide for the preparation of technical sales literature for measuring instruments and process control equipment CPI/704 BS 4478:1969 Methods of measurement of intermodulation products in electronic tubes or valves intended for use in colour television transposers EPL/39 BS 4553:Specification for 600/1000 V single-phase split concentric electric cables BS 4553-1:1998 Cables having PVC insulation GEL/20/17 BS 4553-2:1998 Cables having thermosetting insulation GEL/20/17 BS 4553-3:1998 Cables having thermosetting insulation and low emission of smoke and corrosive gases when affected by fire GEL/20/17 BS 4577:1970 Specification for materials for resistance welding electrodes and ancillary equipment NFE/34 BS 4727:Glossary of electrotechnical, power, telecommunication, electronics, lighting and colour terms. Terms common to power, telecommunications and electronics BS 4727-1:Terms common to power, telecommunications and electronics BS 4727-1:Group 01:1983 Fundamental terminology GEL/1 BS 4727-1:Group 07:1991 Magnetic materials and components GEL/1 BS 4727-1:Group 08:1992 Piezoelectric devices for frequency control and selection GEL/1 BS 4727-2:Terms particular to power engineering BS 4727-2:Group 08:1994 Electric cables GEL/1 BS 4727-2:Group 13:1991 Electrical apparatus for explosive atmospheres GEL/1 BS 4727-2:Group 14:1991 Power capacitors GEL/1 BS 4727-2:Group 15:1991 Overhead lines GEL/1 BS 4727-2:Group 16:1991 Instrument transformers GEL/1 BS 4727-3:Terms particular to telecommunications and electronics BS 4727-3:Group 08:1995 Acoustics and electroacoustics GEL/1 BS 4789:1972 Specification for ceramic components for use in envelopes for electronic tubes EPL/39 BS 5067:1985 Specification for flameproof transformers for use in mines MRE/3 BS 5125:1990 Specification for 50 A 650 V flameproof, restrained and bolted plugs and sockets for use in coal mines MRE/3 BS 5126:Mining type flameproof supply and control units for use on systems up to 1100 V BS 5126-1:1993 Specification for direct-on-line motor starters MRE/3 BS 5126-2:1993 Specification for circuit breaker units MRE/3 BS 5126-3:1993 Specification for air-cooled lighting transformer units MRE/3 BS 5126-4:1993 Specification for air-cooled transformers to power drilling machines MRE/3 BS 5164:1975 Specification for indirect-acting electrical indicating and recording instruments and their accessories PEL/85 BS 5226:1991 Code of practice for equipment and procedures for the cleaning and disinfecting of milking machine installations AW/17 BS 5305:1984 Code of practice for cleaning and disinfecting of plant and equipment used in the dairying industry AW/17 Page 18 of 69 BRITISH STANDARDS REVIEWED AND CONFIRMED BS 5347:1976 Specification for silicon-iron strip-wound cores for use in transformers and inductors for telecommunications and electronic equipment EPL/51 BS 5754:1987 Specification for electrical analogue and state signals for use in coal mines MRE/3 BS 5923:Methods for chemical analysis of rubber BS 5923-2:1980 EDTA titrimetric method for determination of zinc content of rubber products PRI/23 BS 6043:Methods of sampling and test for carbonaceous materials used in aluminium manufacture BS 6043-1:Electrode pitch BS 6043-1.10:2000 Determination of volatile matter content CII/24 BS 6043-1.11:2000 Determination of the atomic C/H ratio of the quinoline-insoluble material CII/24 BS 6043-1.12:1994 Determination of mesophase content CII/24 BS 6043-1.13:2000 Determination of sulfur content CII/24 BS 6043-2:Electrode coke BS 6043-2.4:2000 Analysis by X-ray fluorescence spectroscopy CII/24 BS 6043-2.9:2000 Determination of particle size distribution CII/24 BS 6043-2.10:1996 Determination of electrical resistivity of calcined coke granules CII/24 BS 6043-2.11:1995 Determination of volatile matter content CII/24 BS 6043-2.12:1994 Determination of particle size distribution of fine coke CII/24 BS 6043-2.13:1996 Determination of tapped bulk density of green and calcined coke CII/24 BS 6043-2-18:2001 Determination of the total sulfur by the Eschka method CII/24 BS 6043-2.20:Carboxy reactivity of calcined coke BS 6043-2.20.1:2001 Determination of the reactivity by a loss in mass method CII/24 BS 6043-2.21:Air reactivity of calcined coke BS 6043-2.21.1:2001 Determination of the reactivity by determination of ignition temperature CII/24 BS 6043-3:Electrodes BS 6043-3.1:Sampling BS 6043-3.1.1:1999 Sampling of cathodes CII/24 BS 6043-3.1.2:1999 Sampling of anodes CII/24 BS 6043-3.3:2000 Determination of the bulk density (apparent density) of cathode blocks and prebaked anodes using a dimensions method CII/24 BS 6043-3.4:2000 Determination of the open porosity and bulk density (apparent density) of cathode blocks and prebaked anodes using a hydrostatic method CII/24 BS 6043-3.5:Determination of flexural strength BS 6043-3.5.1:2000 Three point method CII/24 BS 6043-3.6:2000 Determination of electrical resistivity of cathode blocks and prebaked anodes at ambient temperature CII/24 BS 6043-3.8:Carboxy reactivity of prebaked anodes BS 6043-3.8.1:2001 Determination of the reactivity by a loss in mass method CII/24 BS 6043-3.9:Chemical reactivity to air of prebaked anodes BS 6043-3.9.1:2002 Determination of the reactivity by a loss in mass method CII/24 BS 6043-4:Cold ramming pastes BS 6043-4.1:2000 Methods of sampling CII/24 BS 6047:Flame supervision devices for domestic, commercial and catering gas appliances BS 6047-1:1981 Specification for heat sensitive type GSE/22 Page 19 of 69 BRITISH STANDARDS REVIEWED AND CONFIRMED BS 6068:Water quality BS 6068-4:Microbiological methods BS 6068-4.8:Detection and enumeration of the spores of sulfite-reducing anaerobes (Clostridia). Method by enrichment in a liquid medium See BS EN 26461-1. BS 6068-4.13:Detection and enumeration of bacteriophages. Enumeration of somatic coliphages See BS EN ISO 10705-2. BS 6068-5:Biological methods BS 6068-5.28:2000 Determination of long term toxicity of substances to Daphnia magna Straus (Cladocera, Crustacea) EH/3/5 BS 6181:1981 Method of test for air permeability of joints in building B/555 BS 6182:Intrinsically safe power supplies for use in coal mines BS 6182-1:1994 Specification for d.c. power supplies MRE/3 BS 6182-2:1982 Specification for a.c. power supplies MRE/3 BS 6271:1982 Specification for miniature hacksaw blades MTE/20 BS 6346:1997 Electric cables. PVC insulated, armoured cables for voltages of 600/1000 V and 1900/3300 V GEL/20/17 BS 6353:1983 Specification for underground loudspeaker communication systems in coal mines MRE/3 BS 6360:1991 Specification for conductors in insulated cables and cords GEL/20/17 BS 6387:1994 Specification for performance requirements for cables required to maintain circuit integrity under fire conditions GEL/20/18 BS 6469:Insulating and sheathing materials of electric cables BS 6469-99:Test methods used in the United Kingdom but not specified in BS EN 60811 or other parts of BS 6469 BS 6469-99.2:1992 Electrical tests GEL/20/17 BS 6485:1999 PVC-covered conductors for overhead power lines GEL/20/16 BS 6500:2000 Electric cables. Flexible cords rated up to 300/500 V, for use with appliances and equipment intended for domestic, office and similar environments GEL/20/17 BS 6556:Low speed digital signals for use in coal mines BS 6556-1:1985 Specification for optical coupling MRE/3 BS 6556-2:1985 Specification for transformer coupling MRE/3 BS 6556-3:1985 Specification for message protocols MRE/3 BS 6600:Outline dimensions of transformers and inductors for use in telecommunication and electronic equipment BS 6600-1:1987 Specification for the outline dimensions of transformers and inductors using YEI-1 laminations EPL/51 BS 6600-10:1985 Specification for the outline dimensions of transformers and inductors using the Q range of C-cores EPL/51 BS 6704:1996 Code of practice for selection, installation and maintenance of intrinsically safe electrical equipment in coal mines MRE/3 BS 6705:1987 Specification for electrical measuring instruments for use on intrinsically safe circuits in coal mines MRE/3 BS 6708:1998 Flexible cables for use at mines and quarries MRE/3 BS 6709:1986 Specification for interconnection of electrical apparatus, constructed to two or more British Standards, for use in mines susceptible to firedamp MRE/3 BS 6724:1997 Electric cables. Thermosetting insulated, armoured cables for voltages of 600/1000 V and 1900/3300 V, having low emission of smoke and corrosive gases when affected by fire GEL/20/17 BS 6907:Electrical installations for open-cast mines and quarries BS 6907-1:1988 Glossary MRE/3 BS 6907-2:1988 General recommendations for protection against direct contact and electric shock MRE/3 Page 20 of 69 BRITISH STANDARDS REVIEWED AND CONFIRMED BS 6907-3:1988 Recommendations for equipment and ancillaries MRE/3 BS 6907-4:1988 Recommendations for winning, stacking and processing machinery, pumps and low signal level and communications systems MRE/3 BS 6907-5:1988 Recommendations for operation MRE/3 BS 6910:Cold pour resin compound and heat-shrink cable joints in the voltage range up to 1000 V a.c. and 1500 V d.c. BS 6910-1:1988 Specification for materials GEL/20/11 BS 6931:1988 Glossary of terms for copper and copper alloys NFE/34 BS 6940:Total access communication system (T.A.C.S) BS 6940-1:1989 Specification for performance requirements for mobile stations EPL/102 BS 6940-2:1989 Specification for performance and tests of the signalling system of mobile stations EPL/102 BS 6954:Tolerances for building BS 6954-1:1988 Recommendations for basic principles for evaluation and specification B/555 BS 6954-2:1988 Recommendations for statistical basis for predicting fit between components having a normal distribution of sizes B/555 BS 7019:1989 Specification for fully screened 400 A bolted flameproof cable couplers and adaptors for use on systems up to and including 6.6 kV, primarily for use in mines MRE/3 BS 7164:Chemical tests for raw and vulcanized rubber BS 7164-11:Butadiene rubber BS 7164-11.2:1993 Method for determination of unsaturation PRI/23 BS 7194:1990 Specification for direct-current and low-frequency electronic measuring instruments with a digital display PEL/85 BS 7202:1989 Specification for non-incendive low voltage control/interlock and low voltage earth fault monitoring circuits for use in mines MRE/3 BS 7211:1998 Electric cables. Thermosetting insulated, non-armoured cables for voltages up to and including 450/750 V, for electric power, lighting and internal wiring, and having low emission of smoke and corrosive gases when affected by fire GEL/20/17 BS 7383:1990 Specification for cold-pour resin-based compound for use as a filling medium in terminating cables in enclosures for voltages not exceeding 11 kV for use in coal mines MRE/3 BS 7461:1991 Specification for electrically operated automatic gas shut-off valves fitted with throughput adjusters, proof of closure switches, closed position indicator switches or gas flow control GSE/22 BS 7527:Classification of environmental conditions BS 7527-2:Environmental conditions appearing in nature BS 7527-2.1:1991 Temperature and humidity GEL/104 BS 7527-2.2:1991 Precipitation and wind GEL/104 BS 7527-2.3:1991 Air pressure GEL/104 BS 7527-2.4:1991 Solar radiation and temperature GEL/104 BS 7527-2.5:1991 Dust, sand, salt mist GEL/104 BS 7527-2.6:1991 Earthquake vibration and shock GEL/104 BS 7527-2.7:1991 Fauna and flora GEL/104 BS 7562:Planning, design and installation of irrigation schemes BS 7562-1:1992 Glossary of terms AGE/30 BS 7562-2:1992 Guide for acquisition of site data AGE/30 BS 7562-4:1992 Guide to water resources AGE/30 BS 7562-5:1993 Guide for irrigation equipment AGE/30 BS 7562-6:1992 Guide for feasibility and implementation procedures AGE/30 BRITISH STANDARDS REVIEWED AND CONFIRMED Page 21 of 69 BS 7592:1992 Methods for sampling for Legionella organisms in water and related materials EH/3 BS 7629:Specification for 300/500 V fire resistant electric cables having low emission of smoke and corrosive gases when affected by fire BS 7629-1:1997 Multicore cables GEL/20/17 BS 7629-2:1997 Multipair cables GEL/20/17 BS 7655:Specification for insulating and sheathing materials for cables BS 7655-1:Elastomeric insulating compounds BS 7655-1.1:2000 Harmonized types GEL/20/17 BS 7655-1.2:1997 General 90$0DC application GEL/20/17 BS 7655-1.3:2000 XLPE GEL/20/17 BS 7655-1.4:2000 Oil resisting types GEL/20/17 BS 7655-1.5:2000 Flame retardant composites GEL/20/17 BS 7655-1.6:2000 Coil end lead types GEL/20/17 BS 7655-2:Elastomeric sheathing compounds BS 7655-2.1:2000 Harmonized types GEL/20/17 BS 7655-2.3:2000 General application GEL/20/17 BS 7655-2.4:2000 Welding cable covering GEL/20/17 BS 7655-2.6:2000 Sheathing compounds for ships' wiring and offshore applications GEL/20/17 BS 7655-3:PVC insulating compounds BS 7655-3.1:1997 Harmonized types GEL/20/17 BS 7655-3.2:2000 Hard grade types GEL/20/17 BS 7655-4:PVC sheathing compounds BS 7655-4.1:1997 Harmonized types GEL/20/17 BS 7655-4.2:2000 General application GEL/20/17 BS 7655-4.3:2000 Special applications. RF cables GEL/20/17 BS 7655-5:Cross-linked insulating compounds having low emission of corrosive gases, and suitable for use in cables having low emission of smoke when affected by fire BS 7655-5.1:1997 Harmonized cross-linked types GEL/20/17 BS 7655-6:Thermoplastic sheathing compounds having low emission of corrosive gases, and suitable for use in cables having low emission of smoke when affected by fire BS 7655-6.1:1997 General application thermoplastic types GEL/20/17 BS 7655-8:Cross-linked sheathing compounds having low emission of corrosive gases, and suitable for use in cables having low emission of smoke when affected by fire BS 7655-8.1:2000 Harmonized types GEL/20/17 BS 7655-10:Polyethylene sheathing compounds BS 7655-10.1:2000 Thermoplastic medium density polyethylene (MDPE) sheathing compound GEL/20/17 BS 7655-11:Miscellaneous insulating compounds BS 7655-11.1:1997 Harmonized cross-linked PVC types GEL/20/17 BS 7655-12:Miscellaneous sheathing compounds BS 7655-12.1:2000 Harmonized thermoplastic polyurethane sheathing compound GEL/20/17 BS 7769:Electric cables. Calculation of the current rating BS 7769-1:Current rating equations (100% load factor) and calculation of losses BS 7769-1.1:1997 General GEL/20/16 BS 7769-1.2:1994 Sheath eddy current loss factors for two circuits in flat formation GEL/20/16 BS 7769-2:Thermal resistance BRITISH STANDARDS REVIEWED AND CONFIRMED Page 22 of 69 BS 7769-2.2:1997 A method for calculating reduction factors for groups of cables in free air, protected from solar radiation GEL/20/16 BS 7769-3:Sections on operating conditions BS 7769-3.1:1997 Reference operating conditions and selection of cable type GEL/20/16 BS 7771:1994 Code of practice for pasteurization of milk on farms and in small dairies AW/17 BS 7846:2000 Electric cables. 600/1000 V armoured fire-resistant cables having thermosetting insulation and low emission of smoke and corrosive gases when affected by fire GEL/20/17 BS 7852:1997 Code of practice for design of canoes and kayaks GME/33 BS 7870:LV and MV polymeric insulated cables for use by distribution and generation utilities BS 7870-1:1996 General GEL/20/16 BS 7870-2:1999 Methods of test GEL/20/16 BS 7870-4:Specification for distribution cables with extruded insulation for rated voltages of 11 kV and 33 kV BS 7870-4.10:1999 Single-core 11 kV and 33 kV cables GEL/20/16 BS 7870-4.11:1999 Single-core 33 kV lead sheathed cables GEL/20/16 BS 7870-4.20:1999 Three-core 11 kV cables GEL/20/16 BS 7870-5:1999 Polymeric insulated aerial bundled conductors (ABC) of rated voltage 0.6/1 kV for overhead distribution GEL/20/16 BS 7870-6:Specification for 0.6/1 kV and 1.9/3.3 kV power cables with special fire performance for use in power stations BS 7870-6.1:1999 PVC insulated and PVC sheathed cables GEL/20/16 BS 7870-6.2:1999 XLPE or HEPR insulated and PVC sheathed cables GEL/20/16 BS 7870-6.3:1999 Cables with thermosetting insulation and non-halogenated sheath GEL/20/16 BS 7874:1998 Method of test for microbiological deterioration of elastomeric seals for joints in pipework and pipelines PRI/70 BS 7889:1997 Electric cables. Thermosetting insulated, unarmoured cables for a voltage of 600/1000 V GEL/20/17 BS 7924:1999 Code of practice for the repair and overhaul of certified electrical apparatus intended for use in mines susceptible to firedamp MRE/3 BS 9721:1985 Sectional specification for signal transformers of assessed quality for use in electronic equipment for capability approval EPL/51 BS 9727:1985 Sectional specification for power transformers of assessed quality for use in electronic equipment for capability approval EPL/51 BS 9733:1985 Sectional specification for pulse transformers of assessed quality for use in electronic equipment for capability approval EPL/51 BS 9741:1986 Sectional specification for inductors of assessed quality for use in electronic equipment for capability approval EPL/51 BS 9751:1979 Blank detail specification for fixed insulated (unshielded) r.f. inductors at the full assessment level EPL/51 BS 9753:1986 Sectional specification for variable r.f. type inductors of assessed quality for use in electronic equipment for capability approval EPL/51 BS EN ISO 683:Heat-treated steels, alloy steels and free-cutting steels BS EN ISO 683-17:1999 Ball and roller bearing steels ISE/31 BS EN 1622:1998 Water analysis. Determination of the threshold odour number (TON) and threshold flavour number (TFN) EPL/47 BS EN 1976:1998 Copper and copper alloys. Cast unwrought copper products GEL/20/17 BS EN 1977:1998 Copper and copper alloys. Copper drawing stock (wire rod) GEL/20/17 BRITISH STANDARDS REVIEWED AND CONFIRMED Page 23 of 69 BS EN 1978:1998 Copper and copper alloys. Copper cathodes GEL/20/17 BS EN ISO 4957:2000 Tool steels ISE/31 BS EN ISO 6509:1995 Corrosion of metals and alloys. Determination of dezincification resistance of brass ISE/NFE/8 BS EN ISO 7384:1995 Corrosion tests in artificial atmospheres. General requirements ISE/NFE/8 BS EN ISO 7441:1995 Corrosion of metals and alloys. Determination of bimetallic corrosion in outdoor exposure corrosion tests ISE/NFE/8 BS EN ISO 7539:Corrosion of metals and alloys. Stress corrosion testing BS EN ISO 7539-1:1995 General guidance on testing procedures ISE/NFE/8 BS EN ISO 7539-2:1995 Preparation and use of bent-beam specimens ISE/NFE/8 BS EN ISO 7539-3:1995 Preparation and use of U-bend specimens ISE/NFE/8 BS EN ISO 7539-4:1995 Preparation and use of uniaxially loaded tension specimens ISE/NFE/8 BS EN ISO 7539-5:1995 Method for the preparation and use of C-ring specimens ISE/NFE/8 BS EN ISO 7899:Water quality. Detection and enumeration of intestinal enterococci in surface and waste water BS EN ISO 7899-1:1999 Miniaturized method (Most probable number) for surface and waste water EH/3/4 BS EN ISO 7899-2:2000 Membrane filtration method EH/3/4 BS EN ISO 8044:2000 Corrosion of metals and alloys. Basic terms and definitions ISE/NFE/8 BS EN ISO 8565:1995 Metals and alloys. Atmospheric corrosion testing. General requirements for field tests ISE/NFE/8 BS EN ISO 9308:Water quality. Detection and enumeration of Escherichia Coli and coliform bacteria in surface and waste water BS EN ISO 9308-1:2000 Membrane filtration method EH/3/4 BS EN ISO 9308-3:1999 Miniaturized method (most probable number) for the detection and enumeration of E. coli in surface and waste water EH/3/4 BS EN ISO 9400:1996 Nickel-based alloys. Determination of resistance to intergranular corrosion ISE/NFE/8 BS EN 10048:1997 Hot rolled narrow steel strip. Tolerances on dimensions and shape ISE/10 BS EN ISO 10062:1995 Corrosion test in artificial atmospheres at very low concentrations of polluting gas(es) ISE/NFE/8 BS EN 10083:Quenched and tempered steels BS EN 10083-1:1991 Technical delivery conditions for special steels ISE/31 BS EN 10083-2:1991 Technical delivery conditions for unalloyed quality steels ISE/31 BS EN 10083-3:1996 Technical delivery conditions for boron steels ISE/31 BS EN 10084:1998 Case hardening steels. Technical delivery conditions ISE/31 BS EN 10087:1999 Free cutting steels. Technical delivery conditions for semi-finished products, hot rolled bars and rods ISE/31 BS EN 10089:2002 Hot rolled steels for quenched and tempered springs. Technical delivery conditions ISE/31 BS EN 10132:Cold rolled narrow steel strip for heat treatment. Technical delivery conditions BS EN 10132-1:2000 General ISE/31 BS EN 10132-2:2000 Case hardening steels ISE/31 BS EN 10132-3:2000 Steels for quenching and tempering ISE/31 BS EN 10132-4:2000 Spring steels and other applications ISE/31 BS EN 10139:1998 Cold rolled uncoated mild steel narrow strip for cold forming. Technical delivery conditions ISE/10 BS EN 10149:Specification for hot-rolled flat products made of high yield strength steels for cold forming Page 24 of 69 BRITISH STANDARDS REVIEWED AND CONFIRMED BS EN 10149-1:1996 General delivery conditions ISE/10 BS EN 10149-2:1996 Delivery conditions for thermomechanically rolled steels ISE/10 BS EN 10149-3:1996 Delivery conditions for normalized or normalized rolled steels ISE/10 BS EN 10209:1996 Cold rolled low carbon steel flat products for vitreous enamelling. Technical delivery conditions ISE/10 BS EN 10221:1996 Specification for surface quality classes for hot-rolled bars and rods. Technical delivery conditions ISE/31 BS EN 10243:Steel die forgings. Tolerances on dimensions BS EN 10243-1:1999 Drop and vertical press forgings ISE/31 BS EN 10243-2:1999 Upset forgings made on horizontal forging machines ISE/31 BS EN 10250:Open steel die forgings for general engineering purposes BS EN 10250-1:1999 General requirements ISE/31 BS EN 10250-2:2000 Non-alloy quality and special steels ISE/31 BS EN 10250-3:2000 Alloy special steels ISE/31 BS EN 10250-4:2000 Stainless steels ISE/31 BS EN 10254:1999 Steel closed die forgings. General technical delivery conditions ISE/31 BS EN 10267:1998 Ferritic-pearlitic steels for precipitation hardening from hot-working temperatures ISE/31 BS EN 10277:Bright steel products. Technical delivery conditions BS EN 10277-1:1999 General ISE/31 BS EN 10277-2:1999 Steels for general engineering purposes ISE/31 BS EN 10277-3:1999 Free cutting steels ISE/31 BS EN 10277-4:1999 Case-hardening steels ISE/31 BS EN 10277-5:1999 Steels for quenching and tempering ISE/31 BS EN 10278:1999 Dimensions and tolerances of bright steel products ISE/31 BS EN 10292:2000 Continuously hot-dip coated strip and sheet of steels with higher yield strength for cold forming. Technical delivery conditions ISE/10 BS EN ISO 10705:Water quality. Detection and enumeration of bacteriophages BS EN ISO 10705-2:2001 (BS 6068-4.13:2000) Enumeration of somatic coliphages EH/3/4 BS EN ISO 11130:1999 Corrosion of metals and alloys. Alternate immersion test in salt solution ISE/NFE/8 BS EN ISO 11306:1998 Corrosion of metals and alloys. Guidelines for exposing and evaluating metals and alloys in surface sea water ISE/NFE/8 BS EN 12094:Fixed firefighting systems. Components for gas extinguishing systems BS EN 12094-8:1998 Requirements and test methods for flexible connectors for CO$d2 systems GEL/104 BS EN 12500:2000 Protection of metallic materials against corrosion. Corrosion likelihood in atmospheric environment. Classification, determination and estimation of corrosivity of atmospheric environments ISE/NFE/8 BS EN 24506:1993 Specification for hardmetals. Compression test ISE/65 BS EN 26461:Water quality. Detection and enumeration of the spores of sulfite-reducing anaerobes (Clostridia) BS EN 26461-1:1993 (BS 6068-4.8:1993) Method by enrichment in a liquid medium EH/3 BS EN 50109:Hand crimping tools. Tools for the crimp termination of electric cables and wires for low frequency and radio frequency applications BS EN 50109-1:1996 General requirements and tests EPL/46/2 BS EN 50109-2:Particular requirements BRITISH STANDARDS REVIEWED AND CONFIRMED Page 25 of 69 BS EN 50109-2-1:1996 Radio frequency connectors and concentric contacts. Open throat tools with fixed dies, sizes A to E, V and W EPL/46/2 BS EN 50109-2-2:1996 Radio frequency connectors and concentric contacts. Open throat tools with removable and interchangeable dies, sizes A to G, Q to T, V and W EPL/46/2 BS EN 50109-2-3:1996 Contacts of electrical connectors EPL/46/2 BS EN 50109-2-4:1996 Centre contacts of RF connectors, series SMZ EPL/46/2 BS EN 50109-2-5:1996 Termination of twin-ax cable for databus applications EPL/46/2 BS EN 50117:Coaxial cables used in cabled distribution networks BS EN 50117-3:1996 Sectional specification for outdoor drop cables EPL/46/1 BS EN 50117-4:1996 Sectional specification for distribution and trunk cables EPL/46/1 BS EN 50117-5:1997 Sectional specification for indoor drop cables for use in networks operating at frequencies between 5 MHz and 2150 MHz EPL/46/1 BS EN 50117-6:1997 Sectional specification for outdoor drop cables for use in networks operating at frequencies between 5 MHz and 2150 MHz EPL/46/1 BS EN 50262:1999 Cable glands for electrical installations GEL/20/11/1 BS EN 60068:Environmental testing BS EN 60068-1:1995 General and guidance GEL/104 BS EN 60068-2:Test methods BS EN 60068-2-1:1993 Tests A. Cold GEL/104 BS EN 60068-2-2:1993 Tests B. Dry heat GEL/104 BS EN 60068-2-6:1996 Test Fc. Vibration (sinusoidal) GEL/104 BS EN 60068-2-7:1993 Test Ga and guidance. Acceleration, steady state GEL/104 BS EN 60068-2-11:1999 Test KA. Salt mist GEL/104 BS EN 60068-2-13:1999 Test M. Low air pressure GEL/104 BS EN 60068-2-14:2000 Test N. Change of temperature GEL/104 BS EN 60068-2-17:1995 Test Q. Sealing GEL/104 BS EN 60068-2-18:2001 Tests R and guidance. Water GEL/104 BS EN 60068-2-27:1993 Test Ea and guidance. Shock GEL/104 BS EN 60068-2-29:1993 Test Eb and guidance. Bump GEL/104 BS EN 60068-2-30:1999 Test Db and guidance. Damp heat, cyclic (12 + 12 hour cycle) GEL/104 BS EN 60068-2-31:1993 Test Ec. Drop and topple, primarily for equipment-type specimens GEL/104 BS EN 60068-2-32:1993 Test Ed. Free fall GEL/104 BS EN 60068-2-33:2000 Guidance on change of temperature tests GEL/104 BS EN 60068-2-38:1999 Test Z/AD. Composite temperature/humidity cyclic test GEL/104 BS EN 60068-2-39:1999 Test Z/AMD. Combined sequential cold, low air pressure and damp heat test GEL/104 BS EN 60068-2-40:2000 Test Z/AM. Combined cold/low air pressure tests GEL/104 BS EN 60068-2-41:2000 Test Z/BM. Combined dry heat/low air pressure tests GEL/104 BS EN 60068-2-44:1995 Guidance on test T. Soldering GEL/104 BS EN 60068-2-45:1993 Test XA and guidance. Immersion in cleaning solvents GEL/104 BS EN 60068-2-47:2000 Mounting of components, equipment and other articles for vibration, impact and similar dynamic tests GEL/104 BS EN 60068-2-48:2000 Guidance on the application of the tests of IEC 60068 to simulate the effects of storage GEL/104 BS EN 60068-2-52:1996 Test Kb. Salt mist cyclic (sodium chloride solution) GEL/104 BRITISH STANDARDS REVIEWED AND CONFIRMED Page 26 of 69 BS EN 60068-2-55:1993 Test Ee and guidance. Bounce GEL/104 BS EN 60068-2-60:1996 Test Ke. Flowing mixed gas corrosion test GEL/104 BS EN 60068-2-61:1994 Test Z/ABDM. Climatic sequence GEL/104 BS EN 60068-2-65:1995 Test Fg. Vibration, acoustically induced GEL/104 BS EN 60068-2-66:1995 Test Cx. Damp heat, steady state (unsaturated pressurized vapour) GEL/104 BS EN 60068-2-67:1996 Test Cy. Damp heat, steady state, accelerated test primarily intended for components GEL/104 BS EN 60068-2-69:1996 Test Te. Solderability testing of electronic components for surface mount technology by the wetting balance method GEL/104 BS EN 60068-2-70:1996 Test Xb. Abrasion of markings and letterings caused by rubbing of fingers and hands GEL/104 BS EN 60068-2-75:1997 Test Eh. Hammer tests GEL/104 BS EN 60068-3:Guidance BS EN 60068-3-3:1993 Environmental testing. Miscellaneous. Guide to seismic test methods for equipment GEL/104 BS EN 60154:Flanges for waveguides BS EN 60154-1:1996 General requirements EPL/46/2 BS EN 60154-2:1997 Relevant specifications for flanges for ordinary rectangular waveguides EPL/46/2 BS EN 60169:Radio-frequency connectors BS EN 60169-23:1994 Pin and socket connector for use with 3,5 mm rigid precision coaxial lines with inner diameter of outer conductor 3,5 mm (0 ,1378 in) EPL/46/2 BS EN 60169-24:1994 Radio-frequency coaxial connectors with screw coupling, typically for use in 75 ohm cable distribution systems (Type F) EPL/46/2 BS EN 60169-25:1994 Two-pole screw ($9L-20 UNEF) coupled connectors for use with shielded balanced cables having twin inner conductors with inner diameter of outer conductor 13,56 mm (0,534 in) (type TWHN) EPL/46/2 BS EN 60719:1993 Calculation for the lower and upper limits for the average outer dimensions of cables with circular copper conductors and of rated voltages up to and including 450/750 V GEL/20/17 BS EN 60811:Insulating and sheathing materials of electric cables. Common test methods. Methods specific to PVC compounds BS EN 60811-3:Pressure test at high temperature. Tests for resistance to cracking BS EN 60811-3-1:1995 Insulating and sheathing materials of electric cables. Common test methods. Methods specific to PVC compounds GEL/20/17 BS EN 60811-3-2:1995 Insulating and sheathing materials of electric cables. Common test methods GEL/20/17 BS EN 60966:Radio frequency and coaxial cable assemblies BS EN 60966-1:1999 Generic specification. General requirements and test methods EPL/46/1 BS EN 61169:Radio-frequency connectors BS EN 61169-1:1996 Generic specification. General requirements and measuring methods EPL/46/2 BS EN 61169-31:2000 RF coaxial connectors with inner diameter of outer conductor 1,0 mm (0,039 in) with screw coupling. Characteristic impedance 50 ohms (type 1,0) EPL/46/2 BS EN 61169-32:2000 RF coaxial connectors with inner diameter of outer conductor 1,85 mm (0,072 in) with screw coupling. Characteristic impedance 50 ohms (type 1,85) EPL/46/2 BS EN 61580:Methods of measurement for waveguides BS EN 61580-1:1997 Decoupling and rotation of the plane of polarization EPL/46/2 BS EN 61580-2:1997 Level of intermodulation products EPL/46/2 BS EN 61580-7:1997 Graphical method for the determination of waveguide performance EPL/46/2 BS EN 61580-8:1997 Waveguide power holding capability EPL/46/2 BS EN 61580-9:1997 Reflection coefficient at rectangular waveguide interfaces EPL/46/2 Page 27 of 69 BRITISH STANDARDS REVIEWED AND CONFIRMED BS EN 61726:2000 Cable assemblies, cables, connectors and passive microwave components. Screening attenuation measurement by the reverberation chamber method EPL/46 BS EN 62037:2000 RF connectors, connector cable assemblies and cables. Intermodulation level measurement EPL/46 BS EN 122150:1996 Harmonized system of quality assessment for electronic components. Sectional specification: radio frequency coaxial connectors. Series EIA Flange EPL/46 BS EN 122160:1996 Harmonized system of quality assessment for electronic components. Sectional specification: radio frequency coaxial connectors. Series SSMA EPL/46 BS EN 122180:1996 Harmonized system of quality assessment for electronic components. Sectional specification. Radio frequency coaxial connectors. Series SSMC EPL/46/2 BS EN 122190:1996 Harmonized system of quality assessment for electronic components. Sectional specification: radio frequency coaxial connectors. Series 7-16 EPL/46 BS EN 122340:2002 Harmonized system of quality assessment for electronic components. Sectional specification. Radio frequency coaxial connectors. Series MMCX EPL/46/2 DD ENV 302:Adhesives for load-bearing timber structures. Test methods DD ENV 302-5:2002 Determination of the conventional assembly time PRI/52 DD ENV 13999:Adhesives. Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application DD ENV 13999-2:2002 Determination of volatile organic compounds PRI/52 DD ENV 13999-3:2002 Determination of volatile aldehydes PRI/52 DD ENV 13999-4:2002 Determination of volatile diisocyanates PRI/52 BS ISO 3534:Statistics. Vocabulary and symbols BS ISO 3534-3:1999 Design of experiments SS/1 BS ISO 4507:2000 Sintered ferrous materials, carburized or carbonitrided. Determination and verification of case-hardening depth by a micro-hardness test ISE/65 BS ISO/IEC 6523:Information technology. Structure for the identification of organizations and organization parts BS ISO/IEC 6523-1:1998 Identification of organization identification schemes IST/40 BS ISO/IEC 6523-2:1998 Registration of organization identification schemes IST/40 BS ISO 7539:Corrosion of metals and alloys. Stress corrosion testing BS ISO 7539-8:2000 Preparation and use of specimens to evaluate weldments ISE/NFE/8 BS ISO 9403:2000 Crude petroleum. Transfer accountability. Guidelines for cargo inspection PTI/12 BS ISO 10270:1995 Corrosion of metals and alloys. Aqueous corrosion testing of zirconium alloys for use in nuclear power reactors ISE/NFE/8 BS ISO 10405:2000 Petroleum and natural gas industries. Care and use of casing and tubing PSE/17 BS ISO 11463:1995 Corrosion of metals and alloys. Evaluation of pitting corrosion ISE/NFE/8 BS ISO 11782:Corrosion of metal and alloys. Corrosion fatigue testing BS ISO 11782-1:1998 Cycles to failure testing ISE/NFE/8 BS ISO 11782-2:1998 Crack propagation testing using precracked specimens ISE/NFE/8 BS ISO 11846:1995 Corrosion of metals and alloys. Determination of resistance to intergranular corrosion of solution heat-treatable aluminium alloys ISE/NFE/8 BS ISO/IEC 13238:Information technology. Data management BS ISO/IEC 13238-3:1998 IRDS export/import facility IST/40 BS ISO 14976:1998 Surface chemical analysis. Data transfer format CII/60 BRITISH STANDARDS REVIEWED AND CONFIRMED Page 28 of 69 BS ISO 15324:2000 Corrosion of metals and alloys. Evaluation of stress corrosion cracking by the drop evaporation test ISE/NFE/8 BS IEC 60050:International electrotechnical vocabulary BS IEC 60050-101:1998 Mathematics GEL/1 BS IEC 60050-121:1998 Electromagnetism GEL/1 BS IEC 60050-195:1998 Earthing and protection against electric shock GEL/1 BS IEC 60050-351:1998 Automatic control GEL/1 BS IEC 60050-411:1996 Rotating machines GEL/1 BS IEC 60050-442:1998 Electrical accessories GEL/1 BS IEC 60050-551:1998 Power electronics GEL/1 BS IEC 60050-651:1999 Live working GEL/1 BS IEC 60050-705:1995 Radio wave propagation GEL/1 BS IEC 60050-715:1996 Telecommunication networks, teletraffic and operation GEL/1 BS IEC 60050-821:1998 Signalling and security apparatus for railways GEL/1 DD IEC/PAS 62338:2002 Screened balanced cables. Coupling attenuation measurement, triaxial method EPL/46/1 PD 6484:1979 Commentary on corrosion at bimetallic contacts and its alleviation ISE/NFE/8 PD 6634:Vehicle restraint systems PD 6634-1:1999 Fundamentals. Database B/509/1 PD 6634-2:1999 Fundamentals of highway restraint systems B/509/1 PD 6634-3:1999 Development of vehicle highway barriers in the United Kingdom B/509/1 PD 6634-4:1999 Development of bridge parapets in the United Kingdom B/509/1 PD 6634-5:1999 Development of barrier transitions and terminals B/509/1 PD 6634-6:1999 Crashworthy roadside features. Impact attenuators B/509/1 BS G 257:Design of electromagnetic hazard protection of civil aircraft BS G 257-1:1998 Guide to theory and threats ACE/66 BS G 257-2:1998 Guide to protection ACE/66 BS 2M 47:1990 Specification for retreading of cross ply tyres for aircraft ACE/59 BS QC 221100:1997 Radio-frequency connectors. RF coaxial connectors with inner diameter of outer conductor 4,13 mm (0,163 in) with screw coupling. Characteristic impedance 50 ohms (type SMA) EPL/46/2 BS QC 221200:1997 Radio-frequency connectors. RF coaxial connectors with inner diameter of outer conductor 6,5 mm (0,256 in) with bayonet lock. Characteristic impedance 50 ohms (type BNC) EPL/46/2 BS QC 221300:1997 Radio-frequency connectors. RF coaxial connectors with inner diameter of outer conductor 3 mm (0,12 in) with snap-on coupling. Characteristic impedance 50 ohms (type SMB) EPL/46/2 BS QC 221400:1997 Radio-frequency connectors. RF coaxial connectors with inner diameter of outer conductor 3 mm (0,12 in) with screw coupling. Characteristic impedance 50 ohms (type SMC) EPL/46/2 BS QC 222000:1996 Radio-frequency connectors. RF coaxial connectors with inner diameter of outer conductor 6,5 mm (0,256 in) with screw coupling. Characteristic impedance 50 ohms (type TNC) EPL/46/2 BS QC 222100:1997 Radio-frequency connectors. RF coaxial connectors with inner diameter of outer conductor 7 mm (0,276 in) with screw coupling. Characteristic impedance 50 ohms (75 ohms) (type N) EPL/46/2 BRITISH STANDARDS REVIEWED AND CONFIRMED Page 29 of 69 BS QC 222400:1997 Radio-frequency connectors. RF coaxial connectors with inner diameter of outer conductor 5,6 mm (0,22 in). Characteristic impedance 75 ohms (type 1,6/5,6). Characteristic impedance 50 ohms (type 1,8/5,6) with similar mating dimensions EPL/46/2 BS AU 2a:1970 Specification for dimensions of 3$9H - 4$9H in diameter fifth wheel king pin for use with extra heavy duty semi-trailers AUE/13 BS AU 3:1970 Specification for clearance dimensions and fifth wheel positions for tractors and semi-trailers AUE/13 BS AU 25:1964 Specification for towing hook for use between trailers of 5-14 tons gross weight and towing vehicle AUE/13 BS AU 26:1964 Specification for towing jaw for use between trailers of 5-16 tons gross weight and towing vehicle AUE/13 BS AU 27:1964 Specification for towing hook for use between trailers of 5-35 tons gross weight and towing vehicle AUE/13 BS AU 28:1964 Specification for towing jaw for use between trailers of 5-35 tons gross weight and towing vehicle AUE/13 BS AU 29:1964 Specification for drawbar eyes and forecarriage pins for connection between trailers of 5-35 tons gross weight and towing vehicle AUE/13 BS AU 30b:1970 Specification for standard automatic roller-type coupling for semi-trailers of 7 tons to 14$9L tons laden weight AUE/13 BS AU 146b:1970 Specification for standard automatic roller-type coupling for semi-trailers not exceeding 7$9D tons laden weight AUE/13 BS AU 181:1982 Specification for interface dimensions for demountable vehicle body systems AUE/13 BS AU 200:Spray reducing devices for heavy goods vehicles BS AU 200-1a:1984 Specification for design of containment devices AUE/13 BS AU 200-2a:1984 Specification for performance of suppression material and devices, and air/water separating material and devices AUE/13 BS AU 217:Maximum road speed limiters for motor vehicles BS AU 217-1a:1987 Specification for installed requirements AUE/13 BS AU 217-2:1989 Specification for system and component requirements AUE/13 BS 7669-3:1994 Guide to the installation, inspection and repair of safety fences B/509 This standard has been proposed for obsolescence as it is rarely used. BS 7818:1995 Specification for pedestrian restraint systems in metal B/509/1 This standard has been proposed for obsolescence as it is rarely used. BS 9450:1975 Specification for integrated electronic circuits and micro-assemblies of assessed quality (capability approval procedures). Generic data and methods of test EPL/47 This standard has been proposed for confirmation of obsolescence for a further period. BRITISH STANDARDS DECLARED OBSOLESCENT BS 4370:Methods of test for rigid cellular materials BS 4370-1:1988 Methods 1 to 5 PRI/24 This standard has been declared obsolescent as the methods it contains are no longer being used by UK industry. BS 4570:1985 Specification for fusion welding of steel castings WEE/-/1 This standard has been declared obsolescent since although it is still used by some areas of UK industry, there is insufficient support for the preparation of an up-to-date revision. BS 4579:Specification for performance of mechanical and compression joints in electric cable and wire connectors BRITISH STANDARDS PROPOSED FOR DECLARATION OF OBSOLESCENCE BS 2050:1978 Specification for electrical resistance of conducting and antistatic products made from flexible polymeric material PRI/22/-/5 This standard has been proposed for obsolescence as it is not widely used. BS 7669:Vehicle restraint systems BRITISH STANDARDS DECLARED OBSOLESCENT Page 30 of 69 BS 4579-2:1973 Compression joints in nickel, iron and plated copper conductors GEL/20/11 This standard has been declared obsolescent as the committee believe it is no longer widely used for new designs. It should therefore be retained only for existing equipment, and will no longer require maintenance. BS ISO/IEC 9579:2000 Information technology. Remote database access for SQL with security enhancement IST/40 This standard has been declared obsolescent since the international version is not being maintained by ISO/IEC and there is no evidence of its continued use in the UK. BS ISO/IEC ISP 12073:2000 Information technology. International standardized profile FD16 directory data definitions. EDI use of the directory IST/40 This standard has been declared obsolescent since the international version is not being maintained by ISO/IEC and there is no evidence of its continued use in the UK. BS 6579:Safety fences and barriers for highways BS 6579-1:1988 Specification for components for tensioned corrugated beam safety fence on Z posts B/509 This standard has been proposed for withdrawal as it is no longer used in the UK BS 6579-3:1988 Specification for components for tensioned rectangular hollow section beam (100 mm x 100 mm) safety fence B/509 This standard has been proposed for withdrawal as it is no longer used in the UK BS 6579-4:1990 Specification for components for tensioned rectangular hollow section beam (200 mm x 100 mm) safety fence B/509 This standard has been proposed for withdrawal as it is no longer used in the UK BS 6579-5:1986 Specification for open box beam safety fence (single height) B/509 This standard has been proposed for withdrawal as it is no longer used in the UK BS 6579-6:1988 Specification for components for open box beam safety fence (double height) B/509 This standard has been proposed for withdrawal as it is no longer used in the UK BS 6579-7:1989 Specification for components for untensioned corrugated beam safety fence B/509 This standard has been proposed for withdrawal as it is no longer used in the UK BS 6579-8:1987 Specification for concrete safety barriers B/509 This standard has been proposed for withdrawal as it is no longer used in the UK BS 7368:1990 Specification for babies' elastomeric feeding bottle teats CW/42 This standard has been proposed for withdrawal in line with the publication of superseding documents BS EN 14350:2004 Parts 1 & 2 BS 7480:1992 Specification for security seals GW/2 This standard has been proposed for withdrawal as it is no longer relevant. It will be superseded by an ISO standard, which is currently available as a Draft for Development, DD ISO/PAS 17712:2003 BS 7606:1992 Specification for social alarm system apparatus for connection to public switched telephone networks GW/1 This standard has been proposed for withdrawal as it is no longer used in the UK DD IEC PAS 62255:Multi-pair cables used in high bit rate digital access telecommunication networks DD IEC PAS 62255-1:2001 Outdoor cables EPL/46/1 This standard has been proposed for withdrawal as it has been superseded by IEC 62255-1:2003, which has not been adopted by BSI as it conflicts with current European standards PD 6522:1988 Terms relevant to the feather industry for fillings for bedding, upholstery and other domestic articles TCI/66 This standard has been proposed for full withdrawal owing to its complete supersession by BS EN 1885:1998 BRITISH STANDARDS PROPOSED FOR WITHDRAWAL BS 2011:Environmental testing BS 2011-5:Guide to drafting of test methods BS 2011-5.1:1991 General principles GEL/104 This standard has been proposed for withdrawal because it is no longer in general use BS 3648:1963 Specification for cycle rear lamps GME/25 This standard, which was superseded by BS 6102-3:1986 but has remained current owing to its citation in legislation, has been proposed for full withdrawal as it is no longer used by UK industry BRITISH STANDARDS PROPOSED FOR WITHDRAWAL Page 31 of 69 BRITISH STANDARDS WITHDRAWN BS 1608:1990 Specification for electrically driven refrigerant condensing units RHE/4 This standard has been withdrawn as it is no longer current with respect to modern methods and consequently condensing unit manufacturers no longer refer to it BS 3970:Sterilizing and disinfecting equipment for medical products BS 3970-4:1990 Specification for transportable steam sterilizers for unwrapped instruments and utensils LBI/35 Superseded by BS EN 13060:2004 BS 4533:Luminaires BS 4533-102:Particular requirements BS 4533-102.22:1990 Specification for luminaires for emergency lighting CPL/34 Superseded by BS EN 60598-2-22:1999 BS 4897:Trace metal contents of pulps BS 4897-4:1983 Method for determination of manganese content by sodium periodate photometric and flame atomic absorption spectrometric methods PAI/11 Superseded by BS ISO 1830:2005 BS 5224:1995 Specification for masonry cement B/516/10 Superseded by BS EN 413-1:2004 BS 5473:1977 Specification for spinal and abdominal fabric supports CH/168 Superseded by BS 8432:2005 BS 5766:Methods for analysis of animal feeding stuffs BRITISH STANDARDS WITHDRAWN BS 5766-4:1998 Determination of nitrogen content and calculation of crude protein content AW/10 Superseded by BS EN ISO 5983-1:2005 BS 6323:Specification for seamless and welded steel tubes for automobile, mechanical and general engineering purposes BS 6323-6:1982 Specific requirements for cold finished electric resistance welded (including induction welded) steel tubes ISE/8 Superseded by BS EN 10305 Parts 2, 3&6 BS 6955:Calibration of vibration and shock pick-ups BS 6955-4:1994 Method for secondary shock calibration GME/21 Superseded by BS ISO 16063-22:2005 BS 7164:Chemical tests for raw and vulcanized rubber BS 7164-6:Methods for determination of volatile matter BS 7164-6.1:1994 Raw rubber PRI/23 Superseded by BS ISO 248:2005 BS 7426:Specification for high-voltage alternating current switch-fuse combinations See BS EN 60420 BS 7866:1996 Bushings up to 1 kV and from 250 A to 5 kA, for liquid filled transformers PEL/36 Superseded by BS EN 50386:2002 BS 7877:1999 Busbar bushings up to 1 kV and from 1,25 kA to 5 kA, for liquid filled transformers PEL/36/1 Superseded by BS EN 50387:2002 BS EN 12625:Tissue paper and tissue products BS EN 12625-3:1999 Determination of thickness, bulking thickness and apparent bulk density PAI/10 Superseded by BS EN ISO 12625-3:2005 BS EN 12625-4:1999 Determination of tensile strength, stretch at break and tensile energy absorption PAI/10 Superseded by BS EN ISO 12625-4:2005 BS EN 22063:1994 Metallic and other inorganic coatings. Thermal spraying. Zinc, aluminium and their alloys STI/40 Superseded by BS EN ISO 2063:2005 BS EN 50091:Specification for uninterruptible power systems (UPS) BS EN 50091-1-1:1997 General and safety requirements for UPS used in operator access areas PEL/22 Superseded by BS EN 62040-1-1:2003 BS EN 50091-1-2:1999 General and safety requirements for UPS used in restricted access locations PEL/22 Superseded by BS EN 62040-1-2:2003 BS EN 60335:Specification for safety of household and similar electrical appliances BS EN 60335-2:Particular requirements Page 32 of 69 BS EN 60335-2-3:1995 Electric irons CPL/61/30 Superseded by BS EN 60335-2-3:2002 BS EN 60335-2-4:1995 Spin extractors CPL/61 Superseded by BS EN 60335-2-4:2002 BS EN 60335-2-25:1997 Microwave ovens CPL/61/2 Superseded by BS EN 60335-2-25:2002 BS EN 60335-2-70:1996 Milking machines CPL/61 Superseded by BS EN 60335-2-70:2002 BS EN 60335-2-87:1999 Electric animal-stunning equipment CPL/61, CPL/61/8 Superseded by BS EN 60335-2-87:2002 BS EN 60335-2-90:1998 Commercial microwave ovens CPL/61, CPL/61/2 Superseded by BS EN 60335-2-90:2002 BS EN 60420:1993 (BS 7426:1991) Specification for high-voltage alternating current switch-fuse combinations PEL/17/1 Superseded by BS EN 62271-105:2003 BS EN 61000:Electromagnetic compatibility (EMC) BS EN 61000-4-7:1993 General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto GEL/210/8 Superseded by BS EN 61000-4-7:2002 BS ISO/IEC 10728:1993 Information technology. Information resource dictionary system (IRDS) services interface IST/40 This standard has been withdrawn since it has been superseded by ISO/IEC 10728:1993 which is approved with any amendments for use in the UK BS ISO/IEC 11179:Information technology. Specification and standardization of data elements BS ISO/IEC 11179-3:1994 Basic attributes of data elements IST/40 This standard has been withdrawn in line with the withdrawal of the international standard on which it was based BS IEC 50:International electrotechnical vocabulary BS IEC 50(481):1996 Primary cells and batteries GEL/1 This standard has been withdrawn as it has been superseded by IEC 60050-482, which has not been adopted by BSI as it is more readily available via the IEC on-line database BS AU 50:Tyres and wheels BS AU 50-1:Tyres BS AU 50-1.4:Agricultural tractor and machine tyres BS AU 50-1.4.5a:1996 Specification for designations, dimensions, marking and tyre/rim coordination for metric series tyres AUE/4 Superseded by BS ISO 7867-1:2005 BS 5839:Fire detection and alarm systems for buildings BS 5839-8 (Revision) Code of practice for the design, installation, commissioning and servicing of voice alarm systems will supersede BS 5839-8:1998 FSH/12/1 BS 5892:Railway rolling stock materials BS 5892-1 (Revision) Specification for axles for traction and trailing stock will supersede BS 5892-1:1992 RAE/3/-/1 BS 5892-5:1997/Amendment 1 Specification for steel bars for retaining rings for tired wheels RAE/3/-/1 BS 5950:Structural use of steelwork in building BS 5950-1:2000/Amendment 1 Code of practice for design. Rolled and welded sections B/525/31 BS 6297 (Revision) Design and installation of small sewage treatment works and cesspools code of practice will supersede BS 6297:1983 B/505/40 BS 6739 (Revision) Code of practice for instrumentation in process control systems. Installation design and practice will supersede BS 6739:1986 GEL/65 BS 6782:Binders for paints BS 6782-10:1998/Amendment 1 Determination of monomeric and varnishes diisocyanates in polyisocyanate resins STI/3 BS 7273:Code of practice for the operation of fire protection measures Page 33 of 69 NEW WORK STARTED BS 4163 (Revision) Health and safety for design and technology in schools and similar establishments code of practice will supersede BS 4163:2000 GME/27 NEW WORK STARTED BS 7273-1 (Revision) Electrical actuation of gaseous total flooding extinguishing systems will supersede BS 7273-1:2000 FSH/12/4 BS 7533:Pavements constructed with clay, natural stone, or concrete pavers BS 7533-7:2002/Amendment 1 Code of practice for the construction of pavements of natural stone setts and cobbles, and rigid construction with concrete block paving B/507 BS 7533-10:2004/Amendment 1 Guide for the structural design of trafficked pavements constructed of natural stone setts B/507 BS 7941:Methods for measuring the skid resistance of pavement surfaces BS 7941-1 (Revision) Side-way force coefficient routine investigation machine will supersede BS 7941-1:1999 B/510/5 BS 8476 Code of practice for the safe use of concrete pumps B/513/8 BS 8477 Customer satisfaction customer service guidelines SVS/8 BS 11000:Relationship management BS 11000-1 General SVS/8 BS XXXX Specification for diving gases PH/4/7 BS XXXX Code of practice for airtight ceilings and the control of air movements in roofs with airtight ceilings B/542/1 BS XXXX A code of practice for the design of limited access stairs B/208 BS EN 33 (Revision) Pedestal W.C. pans with close-coupled flushing cistern. Connecting dimensions will supersede BS EN 33:2003 B/503 BS EN 40:Lighting columns BS EN 40-1:1992/Amendment 1 Definitions and terms B/509/50 BS EN 287:Qualification test of welders. Fusion welding BS EN 287-1:2004/Amendment 2 Steels WEE/36 BS EN 343:2003/Amendment 1 Protective clothing. Garments for protection against rain PH/3 BS EN 415:Safety of packaging machines BS EN 415-9 Noise measurement methods for packaging machines, packaging lines and auxiliary equipment. Grade 2 and 3 accuracy MCE/3/3 BS EN 754:Aluminium and aluminium alloys. Cold drawn rod/bar and tube BS EN 754-1 (Revision) Technical conditions for inspection and delivery will supersede BS EN 754-1:1997 NFE/35 BS EN 754-2 (Revision) Mechanical properties will supersede BS EN 754-2:1997 NFE/35 BS EN 754-3 (Revision) Round bars, tolerances on dimensions and form will supersede BS EN 754-3:1996 NFE/35 BS EN 754-4 (Revision) Square bars, tolerances on dimensions and form will supersede BS EN 754-4:1996 NFE/35 BS EN 754-5 (Revision) Rectangular bars, tolerances on dimensions and form will supersede BS EN 754-5:1996 NFE/35 BS EN 754-6 (Revision) Hexagonal bars, tolerances on dimensions and form will supersede BS EN 754-6:1996 NFE/35 BS EN 754-7 (Revision) Seamless tubes, tolerances on dimensions and form will supersede BS EN 754-7:1998 NFE/35 BS EN 754-8 (Revision) Porthole tubes, tolerances on dimensions and form will supersede BS EN 754-8:1998 NFE/35 BS EN 755:Aluminium and aluminium alloys. Extruded rod/bar, tube and profiles BS EN 755-1 (Revision) Technical conditions for inspection and delivery will supersede BS EN 755-1:1997 NFE/35 BS EN 755-2 (Revision) Mechanical properties will supersede BS EN 755-2:1997 NFE/35 BS EN 755-3 (Revision) Round bars, tolerances on dimensions and forms will supersede BS EN 755-3:1996 NFE/35 BS EN 755-4 (Revision) Square bars, tolerances on dimensions and form will supersede BS EN 755-4:1996 NFE/35 BS EN 755-5 (Revision) Rectangular bars, tolerances on dimensions and form will supersede BS EN 755-5:1996 NFE/35 Page 34 of 69 NEW WORK STARTED BS EN 755-6 (Revision) Hexagonal bars, tolerances on dimensions and form will supersede BS EN 755-6:1996 NFE/35 BS EN 755-7 (Revision) Seamless tubes, tolerances on dimensions and form will supersede BS EN 755-7:1998 NFE/35 BS EN 755-8 (Revision) Porthole tubes, tolerances on dimensions and form will supersede BS EN 755-8:1998 NFE/35 BS EN 755-9 (Revision) Tolerances on dimensions and form will supersede BS EN 755-9:2001 NFE/35 BS EN 846:Methods of test for ancillary components for masonry BS EN 846-8 (Revision) Determination of load capacity and load-deflection characteristics of joist hangers will supersede BS EN 846-8:2000 B/519 BS EN 943:Protective clothing against liquid and gaseous chemicals, including liquid aerosols and solid particles BS EN 943-1:2002/Amendment C Performance requirements for ventilated and non-ventilated 'gas-tight' (type 1) and 'non-gas-tight' (type 2) chemical protective suits PH/3/8 BS EN ISO/CD 945:Designation of microstructure of cast irons BS EN ISO/CD 945-1 Graphite classification by visual analysis ISE/35 BS EN 970 (Revision) Non-destructive examination of fusion welds. Visual examination will supersede BS EN 970:1997 WEE/46 NEW WORK STARTED BS EN 1071:Advanced technical ceramics. Methods of test for ceramic coatings BS EN 1071-6 (Revision) Determination of the abrasion resistance of coatings by a micro-abrasion wear test will supersede DD ENV 1071-6:2002 RPI/13 BS EN 1459:1999/Amendment 1 Safety of industrial trucks. Self-propelled variable reach trucks MHE/7 BS EN 1634:Fire resistance tests for door and shutter assemblies BS EN 1634-1:2000/Amendment 1 Fire doors and shutters FSH/22 BS EN 1712 (Revision) Non-destructive examination of welds. Ultrasonic examination of welded joints. Acceptance levels will supersede BS EN 1712:1997 WEE/46 BS EN 1714 (Revision) Non-destructive examination of welds. Ultrasonic examination of welded joints will supersede BS EN 1714:1998 WEE/46 BS EN 1745 (Revision) Masonry and masonry products. methods for determining design thermal values will supersede BS EN 1745:2002 B/519 BS EN ISO 3673:Plastics. Epoxy resins BS EN ISO 3673-2 (Revision) Preparation of test specimens and determination of properties will supersede BS EN ISO 3673-2:2000 PRI/42 BS EN ISO 5850:Pulp. Estimation of dirt and shives BS EN ISO 5850-1 Inspection of laboratory sheets by transmitted light PAI/11 BS EN ISO 6141 Gas analysis. Requirements for certificates for calibration gases and gas mixtures will supersede BS 4559-4:2000 PTI/15 BS EN ISO 6143 Gas analysis. Comparison methods for determining and checking the composition of calibration gas mixtures will supersede BS ISO 6143:2001 PTI/15 BS EN ISO 6144 Gas analysis. Preparation of calibration gas mixtures. Static volumetric method will supersede BS ISO 6144:2003 PTI/15 BS EN ISO 8662:Hand-held portable power tools. Measurement of vibrations at the handle BS EN ISO 8662-4 (Revision) Angle and vertical grinders will supersede BS EN ISO 8662-4:1995 MCE/8 BS EN ISO 11040:Prefilled syringes BS EN ISO 11040-4 Glass barrels for injectables CH/212 BS EN ISO 11058 (Revision) Geotextiles and geotextile related products. Determination of water permeability characteristics normal to the plane, without load will supersede BS EN ISO 11058:1999 B/553 BS EN 12020:Aluminium and aluminium alloys. Extruded precision profiles in EN-AW-6060 and EN-AW-6063 BS EN 12020-1 (Revision) Technical conditions for inspection and delivery will supersede BS EN 12020-1:2001 NFE/35 Page 35 of 69 BS EN 12020-2 (Revision) Tolerances on dimensions and form will supersede BS EN 12020-2:2001 NFE/35 BS EN 12691 (Revision) Flexible sheets for waterproofing. Bitumen, plastic and rubber sheets for roof waterproofing. Determination of resistance to impact will supersede BS EN 12691:2001 B/546 BS EN ISO 12956 (Revision) Geotextiles and geotextile related products. Determination of the characteristic opening size will supersede BS EN ISO 12956:1999 B/553 BS EN ISO 12958 (Revision) Geotextiles and geotextile related products. Determination of water flow capacity in their plane will supersede BS EN ISO 12958:1999 B/553 BS EN 13126:Building hardware. Hardware for windows and balcony doors. Requirements and test methods BS EN 13126-15 Rollers B/538/4 BS EN 13126-16 Fittings for lift and slide systems B/538/4 BS EN 13126-17 Fittings for tilt and slide systems B/538/4 BS EN 13234 (Revision) Advanced technical ceramics. Ceramic composites mechanical properties at ambient temperature. Evaluation of the resistance to crack propagation by notch sensitivity testing will supersede DD ENV 13234:2000 RPI/13 BS EN 13235 (Revision) Advanced technical ceramics. Ceramic composites mechanical properties at high temperature under inert atmosphere. Determination of creep behaviour will supersede DD ENV 13235:2000 RPI/13 BS EN 13381:Test methods for determining the contribution to the fire resistance of structural members BS EN 13381-1 Horizontal protective membranes FSH/22 BS EN 13501:Fire classification of construction products and building elements BS EN 13501-1 (Revision) Classification using test data from reaction to fire tests will supersede BS EN 13501-1:2002 FSH/21 BS EN 13501-2 (Revision) Classification using data from fire resistance tests, excluding ventilation services will supersede BS EN 13501-2:2003 FSH/22 BS EN 13611 (Revision) Safety and control devices for gas burners and gas burning appliances. General requirements will supersede BS EN 13611:2000 GSE/22 BS EN 13618:Water supply. Hose assemblies BS EN 13618-1 Flexible hose assemblies with or without braiding B/503 BS EN 13618-2 Semi rigid assemblies with or without braiding B/503 BS EN ISO 13736 (Revision) Petroleum products and other liquids. Determination of flash point. Abel closed cup method will supersede BS EN ISO 13736:1998 PTI/13 BS EN 14459 Methods of risk analysis for the use of electronics in systems and control functions for gas burners and gas burning appliances GSE/22 BS EN ISO 14896:2001/Corrigendum 1 Plastics. Polyurethane raw materials. Determination of isocyanate content PRI/42 BS EN ISO 15011:Health and safety in welding and allied processes. Laboratory method for sampling fume and gases BS EN ISO 15011-3 (Revision) Determination of ozone emission rate will supersede BS EN ISO 15011-3:2002 WEE/40 BS EN 15287:Chimneys. Design, installation and commissioning of chimneys BS EN 15287-1 Chimneys for non-roomsealed heating appliances B/506 BS EN 15318 Design and application of gypsum blocks B/544/1 BS EN 15320 Identification card systems. Surface transport applications. Interoperable public transport application (IOPTA) IST/17 BS EN ISO 17249:2004/Amendment 1 Safety footwear with resistance to chain saw cutting PH/1 BS EN ISO 20344:2004/Amendment 1 Personal protective equipment. Test methods for footwear PH/1 NEW WORK STARTED Page 36 of 69 BS EN ISO 20345:2004/Amendment 1 Personal protective equipment. Safety footwear PH/1 BS EN ISO 20346:2004/Amendment 1 Personal protective equipment. Protective footwear PH/1 BS EN ISO 20347:2004/Amendment 1 Personal protective equipment. Occupational footwear PH/1 BS EN ISO 23747 Lung ventilators and related equipment. Peak expiratory flow meters will supersede BS EN 13826:2003 CH/121/3 BS EN 60050:International electrotechnical vocabulary BS EN 60050-411 (Edition 3) Rotating machinery will supersede BS IEC 60050(411):1996 PEL/2 BS EN 60598:Luminaires BS EN 60598-2-20:1998/Corrigendum 4 Particular requirements for lighting chains CPL/34/4 BS EN 61338:Waveguide type dielectric resonators BS EN 61338-1-4 (Edition 1) General information and test conditions. Measurement method of complex relative permittivity for dielectric resonator materials at millimeter-wave frequency EPL/49 BS EN 61788:Superconductivity BS EN 61788-7 (Revision) Electronic characteristic measurements. Surface resistance of superconductors at microwave frequencies will supersede BS EN 61788-7:2002 L/-/90 BS EN 62271:High-voltage switchgear and controlgear BS EN 62271-104 Alternating current switches for rated voltages of 52kv and above PEL/17/1 BS EN 62368 Audio/video, information and communication technology equipment. Safety requirements EPL/108 BS EN 62442:Energy efficiency of electrical lighting equipment. Ballasts for fluorescent lamps BS EN 62442-1 Method of measurement to determine energy consumption of ballast-lamp circuits CPL/34/3 BS EN 00256124:Measurement of axle loads BS EN 00256124-1 Interoperable 'in-service' rail vehicles RAE/1 BS EN 261339 Packaging. Flexible aluminium tubes test method to determine the porosity of the internal coating PKW/0 BS EN 261340 Packaging. Flexible laminate tubes test methods to determine the strength of the head welding PKW/0 BS EN 261341 Packaging. Flexible laminate and plastic tubes test method to determine the print adhesion PKW/0 BS EN 261342 Packaging. Flexible laminate tubes test methods to determine the strength of the side seam PKW/0 BS EN 261343 Packaging. Flexible aluminium tubes determination of the adhesion of the internal and external protective lacquering PKW/0 BS ISO 3937:Cutters arbors with tenon drive BS ISO 3937-2 7/24 taper. Dimensions MTE/5 BS ISO 3937-3 Hollow taper interface with flange contact surface. Dimensions MTE/5 BS ISO 4252 Agricultural tractors. Operator's workplace, access and exit. Dimensions AGE/6 BS ISO 4411 Hydraulic fluid power. Valves. Determination of pressure differential / flow characteristics MCE/18 BS ISO 4625:Binders for paints and varnishes. Determination of softening point BS ISO 4625-1:2004/Amendment 1 Ring-and-ball method STI/3 BS ISO 4625-2:2004/Amendment 1 Cup-and-ball method STI/3 BS ISO 5667:Water quality. Sampling BS ISO 5667-15 Guidance on the preservation and handling of sludge and sediment samples will supersede BS 6068-6.15:1999 EH/3/6 NEW WORK STARTED Page 37 of 69 BS ISO 5667-17 (Revision) Guidance on sampling of suspended sediments will supersede BS ISO 5667-17:2000 EH/3/6 BS ISO 6538:Pneumatic fluid power. Determination of flow-rate characteristics of components using compressible fluids BS ISO 6538-1 General rules for components with fixed orifice MCE/18 BS ISO 6538-2 General rules for components with variable or fixed orifices MCE/18 BS ISO 6538-3 Discharge methods for components with variable or fixed orifices MCE/18 BS ISO 6538-4 Charge method for components with variable or fixed orifices MCE/18 BS ISO 6538-5 Alternative test methods. Simple discharge test MCE/18 BS ISO 7302 Cereals and cereal products. Determination of total fat content AW/4 BS ISO 8178:Reciprocating internal combustion engines. Exhaust emission measurement BS ISO 8178-3 (Revision) Definitions and methods of measurement of exhaust gas smoke under steady state conditions will supersede BS ISO 8178-3:1994 MCE/14/-/5 BS ISO 8178-5 Test fuels MCE/14/-/5 BS ISO 8468 Ships and marine technology ships bridge layout and associated equipment. Requirements and guidelines will supersede BS EN ISO 8468:1995 SME/32/5 BS ISO 9241:Ergonomics of human-system interaction BS ISO 9241-20 Guidance for the accessibility of information communication equipment and services PH/9 BS ISO 9413 Tyre valves. Dimensions and designation will supersede BS AU 50-3.1E:2004 AUE/4 BS ISO 9612 Acoustics. Measurement and calculation of occupational noise engineering method EH/1/3 BS ISO 9635:Agricultural irrigation equipment. Irrigation valves BS ISO 9635-3 Check valves AGE/30 BS ISO 10110:Optics and photonics. Preparation of drawings for optical elements and systems BS ISO 10110-7 (Revision) Surface imperfection tolerances will supersede BS ISO 10110-7:1996 CPW/172/1 BS ISO 11178:Tractors and machinery for agriculture and forestry. Serial control and communications data network BS ISO 11783-3 (Revision) Data link layer will supersede BS ISO 11783-3:1998 AGE/6 BS ISO 12003:Agriculture and forestry tractors. Narrow-track wheeled tractors BS ISO 12003-2 (Revision) Rear-mounted roll-over protective structures will supersede BS ISO 12003-2:2002 AGE/6 BS ISO 12635 (Revision) Durability of wood and wood-based products. Qualitative determination of quaternary ammonium compounds in wood will supersede BS ISO 12635:1996 PAI/43 BS ISO 14132:Optics and photonics. Vocabulary for telescopic systems BS ISO 14132-5 Terms for night vision systems CPW/172 BS ISO/IEC 14496:Information technology. Coding of audio-visual objects BS ISO/IEC 14496-9 Reference hardware description IST/37 BS ISO 15715:2003/Amendment 1 Binders for paints and varnishes. Determination of turbidity STI/3 BS ISO 15819 Cosmetics. Nitrosamines. Detection and determination of n-nitrosodiethanolamine (NDELA) in cosmetics by HPLC-MS-MS CW/217 BS ISO 16212 Cosmetics. Microbiology. Enumeration of yeast and mould CW/217 BS ISO 17382 Oil of magnolia flower, China (Michelia alba DC) AW/54 BS ISO/IEC 18047:Information technology. Automatic identification and data capture techniques BS ISO/IEC 18047-2 RFID device conformance test methods IST/34 NEW WORK STARTED Page 38 of 69 BS ISO/IEC 18047-6 International symbology specification. Data matrix IST/34 BS ISO 18072:Ships and marine technology ship structures BS ISO 18072-2 Requirements for their ultimate limit state assessment SME/32/8 BS ISO 19072:Road vehicles. Connection interface for pyrotechnic devices, two way and three way connections BS ISO 19072-2 Test methods and general performances requirements AUE/16 BS ISO 19712:Plastics. Classification and performance of decorative solid surfacing material BS ISO 19712-1 Classification and specifications PRI/76 BS ISO 19712-2 Sheet goods PRI/76 BS ISO 21094 Optics and photonics. Telescopic systems. Specifications for night vision devices CPW/172 BS ISO 21100 Air cargo unit load devices. Performance requirements and test parameters ACE/57 BS ISO 21138:Plastics piping systems for non-pressure underground drainage and sewerage. Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) BS ISO 21138-1 Material and performance specifications for pipes, fittings and the systems PRI/88/1 NEW WORK STARTED BS ISO 21138-2 Pipes with smooth external surface (all materials), type a PRI/88/1 BS ISO 21138-3 Pipes with a non-smooth external surface (all materials), type b PRI/88/1 BS ISO 21212 Intelligent transport systems. Communications, air-interface, long and medium range (CALM). 2G cellular systems EPL/278 BS ISO 21213 Intelligent transport systems. Communications, air-interface, long and medium range (CALM). 3G cellular systems EPL/278 BS ISO 21299 Agriculture and forestry machinery equipment. Powered ride-on equipment for turf maintenance applications. Roll-over protective structures (ROPS). Test procedures and acceptance criteria AGE/20 BS ISO 22036 Soil quality. Determination of trace elements in extracts of soil by inductively coupled plasma-atomic emission spectrometry (ICP-AES) EH/4 BS ISO 22574 Road vehicles. Brake linings. Friction materials. Visual inspection AUE/11 BS ISO 22856 Equipment for crop protection. Laboratory drift methods measurements. Wind tunnels AGE/15 BS ISO 23392 Fresh and quick-frozen maize and peas. Determination of alcohol-insoluble solids content AW/100 BS ISO 23996 Resilient floor coverings. Determination of density PRI/60 BS ISO 23997 Resilient floor coverings. Determination of mass per unit area PRI/60 BS ISO 23999 Resilient floor coverings. Determination of dimensional stability and curling after exposure to heat PRI/60 BS ISO 24153:Random sampling procedures BS ISO 24153-1 Quality control and designed experiment applications SS/5 BS ISO 24353 Hygrothermal performance of building materials and products. Determination of moisture adsorption/desorption properties in response to humidity variation B/540/8 BS ISO 24597 Microbeam analysis. Scanning electron microscopy. Measurement methods for image resolution CII/9 BS ISO/IEC 24745 Information technology. Security techniques. Biometric template protection IST/33 BS ISO/IEC TR 24800:JPSearch BS ISO/IEC TR 24800-1 System framework and components IST/37 BS ISO 25780 Plastics piping systems for pressure and non-pressure water supply, irrigation or drainage and sewerage. Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin. Components intended to be installed using trenchless PRI/88/2 Page 39 of 69 BS ISO/IEC 81060:Non-invasive sphygmomanometers BS ISO/IEC 81060-1 Requirements and test methods for mechanical type CH/62/4 BS ISO XXXXXX Water quality. Determination of individual isomers of nonylphenol. Method by solid phase extraction EH/3/2 BS ISO XXXXXX Water quality. Determination of perfluorooctanesulfonate (PFOS) and perfluorooctanoate (PFOA) in un-filtrated water samples. Method by solid phase extraction and liquid chromatograph-mass spectrometry EH/3/2 BS IEC 60412 Scintillation detectors nomenclature/type numbering standard dimensions of scintillators will supersede BS 5210:1975 NCE/2 BS IEC 60601:Medical electrical equipment BS IEC 60601-2-44 (Edition 3) Particular requirements for the safety of X-ray equipment for computed tomography will supersede BS EN 60601-2-44:2001 CH/62/2 BS IEC 60976 Medical electrical equipment. Medical electron accelerators. Functional performance characteristics CH/62/3 BS IEC 60988 Acoustic monitoring systems for loose parts detection. Characteristics, design criteria and operational procedures NCE/8 BS IEC 61227 Nuclear power plants. Control rooms. Operator controls NCE/8 BS IEC 61453 Nuclear instrumentation. Scintillation detector systems of gamma-ray energies for assay of radionuclides. Calibration and usage NCE/2 BS IEC 61772 Nuclear power plants. Main control room. Application of visual display units (VDU) NCE/8 BS IEC 61948:Nuclear medicine instrumentation. Routine tests BS IEC 61948-4 Radionuclide calibrators CH/62/3 BS IEC 62232 Methods for the assessment of electric, magnetic and electromagnetic fields associated with human exposure GEL/106 DD CLC/TS 16587 Railway applications. Rolling stock. Electric equipment in trolley buses. Safety requirements and connection systems GEL/9/2 PD 5500 (Revision) Specification for fusion welded pressure vessels will supersede PD 5500:2003 PVE/1 PD 8010:Code of practice for pipelines PD 8010-3 Codified approach for the on-shore application of pipeline risk assessment for lUP advice to local planning authorities PSE/17/2 PD CEN ISO/TR 3834:Quality requirements for welding. Fusion welding of metallic materials PD CEN ISO/TR 3834-6 Guidance on implementing ISO 3834 WEE/-/1 DRAFT BRITISH STANDARDS FOR PUBLIC COMMENT 05/00422006 DC prEN 1548 Flexible sheets for waterproofing. Plastic and rubber sheets for roof waterproofing. Method for exposure to bitumen B/546/2 Comments for the above document are required by 15 November, 2005 05/19976767 DC BS ISO 11783-10 Tractors and machinery for agriculture and forestry. Serial control and communications data network. Part 10. Task controller and management information system data interchange AGE/6 05/19978685 DC BS EN 74-3 Couplers, spigot pins and base plates for use in falsework and scaffolds. Part 3. Plain base plates and spigot pins. Requirements and test methods B/514/21 05/19982631 DC BS ISO 9150 Protective clothing. Determination of behaviour of materials on impact of small splashes of molten metal PH/3/2 05/19990229 DC BS ISO 9928-2 Cranes. Crane driving manual. Part 2. Mobile cranes MHE/3/5 Comments for the above document are required by 24 October, 2005 05/30057604 DC BS 8504-1 Beach safety flags. Part 1. Colour, shape and meaning PH/8/2/1 05/30057907 DC BS 6465-1 Sanitary installations. Part 1. Code of practice for design of sanitary facilities and scale of provision of sanitary appliances B/503 05/30059424 DC ISO 19134 Geographic information. Location based services. Multimodal routing and navigation IST/36 DRAFT BRITISH STANDARDS FOR PUBLIC COMMENT Page 40 of 69 05/30067086 DC EN 203-2-7 Gas heated catering equipment. Part 2-7. Specific requirements. Salamanders and rotisseries GSE/19 05/30075032 DC ISO 23181 Hydraulic fluid power. Filter elements. Determination of resistance to flow fatigue using high viscosity fluid MCE/18/-/6 05/30082472 DC BS 7121-1 Code of practice for safe use of cranes. Part 1. General MHE/3/11 Comments for the above document are required by 31 October, 2005 05/30086722 DC EN 15329 Railway applications. Braking. Brake block holder and brake shoe key for railway vehicles RAE/4 05/30086725 DC EN 15328 Railway applications. Braking. Brake pads RAE/4 05/30090874 DC EN 15327-1 Railway applications. Passenger alarm subsystem. Part 1. General requirements and passenger interface for the passenger emergency brake system RAE/4 05/30091636 DC ISO 14577-4 Metallic materials. Instrumented indentation test for hardness and materials parameters. Part 4. Test method for metallic and non-metallic coatings ISE/NFE/4/5 05/30093062 DC prEN 15269-2 Extended application of test results for doorsets and shutter assemblies. For doors and shutters. Part 2. Steel hinged and pivoted doorsets £18.00 members £36.00 non-members FSH/22 05/30095753 DC ISO 7500-2 Metallic materials. Verification of static uniaxial testing machines. Part 2. Tension creep testing machines. Verification of the force applied ISE/NFE/4/1 05/30097610 DC BS ISO 23714 Pulps. Determination of water retention value (WRV) PAI/11 Comments for the above document are required by 14 November, 2005 05/30098235 DC ISO 21081-1 Hydraulic fluid power. Monitoring the level of particulate contamination of the fluid. Part 1. General principles MCE/18/-/6 05/30098238 DC ISO 21081-2 Hydraulic fluid power. Monitoring the level of particulate contamination of the fluid. Part 2. Filter blockage technique MCE/18/-/6 05/30099720 DC EN 12368 Traffic control equipment. Signal heads EPL/526 05/30099723 DC EN 12352 Traffic control equipment. Warning and safety light devices EPL/526 05/30102528 DC IEC 62385 Nuclear power plants. Instrumentation and control important to safety. Methods for assessing the performance of safety system instrument channels NCE/2 05/30102865 DC EN ISO 19493 Water quality. Guidance on marine biological surveys of littoral and sublittoral hard bottoms EH/3/5 05/30103531 DC BS IEC 62275 Cable management. Cable ties for cable installations PEL/213 Comments for the above document are required by 28 October, 2005 05/30106456 DC IEC 62282-6 Fuel cell technologies. Part 6-1. Micro fuel cell power systems. Safety £18.00 members £36.00 non-members GEL/105 05/30107743 DC ISO/IEC 19794-7 Biometric data interchange. Part 7. Signature/sign data IST/44 Comments for the above document are required by 31 October, 2005 05/30107760 DC ISO/IEC 24713-1 Biometric profiles for interoperability and data interchange. Part 1. Biometric reference architecture IST/44 Comments for the above document are required by 31 October, 2005 05/30111064 DC BS 7291-1 Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings. Part 1. General requirements PRI/88/2 Comments for the above document are required by 31 December, 2005 05/30111066 DC BS 7291-2 Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings. Part 2. Specification for polybutylene (PB) pipes and associated fittings PRI/88/2 Comments for the above document are required by 31 December, 2005 05/30111068 DC BS 7291-3 Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings. Part 3: Specification for cross-linked polyethylene (PE-X) pipes and associated fittings PRI/88/2 Comments for the above document are required by 31 December, 2005 DRAFT BRITISH STANDARDS FOR PUBLIC COMMENT Page 41 of 69 05/30111479 DC ISO/IEC 19794-8 Biometrics. Biometric data interchange formats. Part 8. Finger pattern skeletal data IST/44 05/30113382 DC BS ISO 21630 Pumps. Testing. Submersible mixers for wastewater and similar applications MCE/6 Comments for the above document are required by 31 October, 2005 05/30115485 DC EN 1739 Determination of shear strength for in-plane forces of joints between prefabricated components made of autoclaved aerated concrete or lightweight aggregate concrete with open structure B/523 Comments for the above document are required by 15 November, 2005 05/30115489 DC EN 15304 Determination of the freeze-thaw resistance of autoclaved aerated concrete B/523 Comments for the above document are required by 15 November, 2005 05/30117679 DC IEC 60515 ED 2 Nuclear power plants. Instrumentation important to safety. Radiation detectors. Characteristics and test methods NCE/8 05/30118212 DC BS 8469 Personal protective equipment for fire-fighters. Assessment of ergonomic performance and compatibility. Requirements and test methods PH/14 Comments for the above document are required by 31 October, 2005 05/30122495 DC IEC 62153-4-1 Metallic communication cable test methods. Part 4-1. Electro magnetic compatibility (EMC). Introduction to electromagnetic (EMC) screening measurements EPL/46 05/30122498 DC IEC 62153-4-0 Metallic communication cable test methods. Part 4-0. Electro magnetic compatibility (EMC). Relationship between surface transfer impedance and screening attenuation, recommended limits EPL/46 05/30123357 DC BS 8504-2 Beach safety flags. Part 2. Materials PH/8/2/1 05/30124529 DC ISO 20552 Workplace air. Determination of mercury vapour. Method using gold-amalgam collection and analysis by atomic absorption spectrometry or atomic fluorescence spectrometry EH/2/2 05/30126248 DC BS EN 71-5 Safety of toys. Part 5. Chemical toys (sets) other than experimental sets CW/15 Comments for the above document are required by 15 October, 2005 05/30127022 DC ISO 4928 Road vehicles. Elastomeric cups and seals for cylinders for hydraulic braking systems using a non-petroleum base hydraulic brake fluid (service temperature 120$0DC max.) PRI/69 05/30127561 DC BS 8470 Code of practice for the secure destruction of confidential material GW/2 05/30127645 DC ISO 15364 Ships and marine technology. Pressure/vacuum valves for cargo tanks SME/32/3 05/30128342 DC ISO 15223-1 Medical devices. Symbols to be used with medical device labels, labelling, and information to be supplied. Part 1. General requirements CH/210/3 05/30128661 DC EN 13779 Ventilation for non residential buildings. Performance requirements for ventilation and room-conditioning systems RHE/2 05/30129194 DC EN 15317 Non-destructive testing. Ultrasonic testing. Characterization and verification of ultrasonic thickness measuring equipment WEE/46 05/30129363 DC ISO 9170-1 Terminal units for medical gas pipeline systems. Part 1. Terminal units for use with compressed medical gases and vacuum CH/121/6 05/30129368 DC ISO 9170-2 Terminal units for medical gas pipeline systems. Part 2. Terminal units for anaesthetic gas scavenging systems CH/121/6 05/30129374 DC ISO 15002 Flow-metering devices for connection to terminal units of medical gas pipeline systems CH/121/6 05/30129688 DC IEC 61156-5-1 ED 2 Multicore and symmetrical pair/quad cables for digital communications. Part 5-1. Symmetrical pair/quad cables with transmission characteristics up to 600 MHz. Horizontal floor wiring. Blank detail specification EPL/46 05/30133088 DC BS ISO 18332 Metallic and other inorganic coatings. Definitions and conventions concerning porosity STI/33 Comments for the above document are required by 28 October, 2005 05/30133509 DC BS 7593 Code of practice for treatment of water in domestic hot water central heating systems CII/62 Comments for the above document are required by 31 December, 2005 DRAFT BRITISH STANDARDS FOR PUBLIC COMMENT Page 42 of 69 05/30133687 DC BS EN 1269 A1 Textile floor coverings. Assessment of impregnations in needled floor coverings by means of a soiling test PRI/3 05/30135018 DC ISO/IEC 24711 Method for determination of ink cartridge yield for color inkjet printers and multifunction devices that may contain printer components IST/3 05/30135332 DC BS 6102-3 A4 Cycles. Part 3. Specification for photometric and physical requirements of lighting equipment GME/25 05/30135987 DC EN 161 Automatic shut-off valves for gas burners and gas appliances GSE/22 05/30136075 DC ISO 1841 Cosmetics. Microbiology. Detection of Candida albicans CW/217 Comments for the above document are required by 31 October, 2005 05/30137202 DC ISO/IEC 18000-6 A1 Information technology. Radio frequency identification for item management. Part 6. Parameters for air interface communications at 860 MHz to 960 MHz £18.00 members £36.00 non-members IST/34 Comments for the above document are required by 31 October, 2005 05/30137420 DC IEC 60086-1 Primary batteries. Part 1. General CPL/35 05/30137514 DC IEC 60747-14-4 Discrete semiconductor devices. Part 14-4. Semiconductor accelerometers £18.00 members £36.00 non-members EPL/47 05/30137551 DC ISO 21415-2 Wheat and wheat flour. Gluten content. Part 2. Determination of wet gluten by mechanical means AW/4 05/30137579 DC EN 13834 Cookware. Ovenware for use in traditional domestic ovens CW/9 05/30137582 DC ISO 24497-1 Non-destructive testing. Metal magnetic memory. Part 1. General requirements WEE/46 05/30137585 DC ISO 24497-2 Non-destructive testing. Metal magnetic memory. Part 2. Terms and definitions WEE/46 05/30137588 DC ISO 24497-3 Non-destructive testing. Metal magnetic memory. Part 3. Inspection of welds WEE/46 05/30137603 DC ISO 24014-1 Public transport. Interoperable fare management system. Part 1. Architecture EPL/278 05/30137614 DC ISO 18672-1 Plastics piping systems for non-pressure drainage and sewerage. Polyester resin concrete (PRC). Part 1. Pipes and fittings with flexible joints PRI/88/2 05/30137621 DC EN 1564/prA1 Founding. Austempered ductile cast irons ISE/35 Comments for the above document are required by 28 October, 2005 05/30137627 DC EN ISO 16000-7 Indoor air. Part 7. Sampling strategy for determination of airborne asbestos fibre concentrations EH/2/3 05/30137694 DC ISO 21501-2 Determination of particle size distribution. Single particle light-interaction methods. Part 2. Light-scattering liquid-borne particle counter LBI/37 05/30137697 DC ISO 21501-3 Determination of particle size distribution. Single particle light-interaction methods. Part 3. Light-extinction liquid-borne particle counter LBI/37 05/30137700 DC ISO 21501-4 Determination of particle size distribution. Single particle light-interaction methods. Part 4. Light-scattering airborne particle counter for clean spaces LBI/37 05/30137717 DC EN 15312 Free access multi-sports equipment. Requirements, including safety and test methods SW/65 05/30137729 DC ISO 8061 AMD 3 Alpine ski-bindings. Selection of release torque values SW/136 05/30137732 DC ISO 11088 AMD 1 Assembly, adjustment and inspection of an alpine ski-binding-boot (S-B-B) system SW/136 05/30137735 DC ISO 22264 Telemark ski-boots for adults. Interface with Telemark ski-bindings. Requirements and test methods SW/136 05/30137738 DC ISO 9523 Touring ski-boots for adults. Interface with touring ski-bindings. Requirements and test methods SW/136 DRAFT BRITISH STANDARDS FOR PUBLIC COMMENT Page 43 of 69 05/30137754 DC ISO/IEC 18004 Information technology. Automatic identification and data capture techniques. Bar code symbology specification. QR code £18.00 members £36.00 non-members IST/34 05/30137789 DC BS ISO 12465 Plywood. Specifications B/541 05/30137797 DC IEC 61400-25-1 ED 1 Wind turbines. Part 25-1. Communications for monitoring and control of wind power plants. Overall description of principles and models PEL/88 05/30137801 DC IEC 61400-25-2 ED 1 Wind turbines. Part 25-2. Communications for monitoring and control of wind power plants. Information models PEL/88 05/30137805 DC IEC 61400-25-3 ED 1 Wind turbines. Part 25-3. Communications for monitoring and control of wind power plants. Information exchange models PEL/88 05/30137809 DC IEC 61400-25-4 ED 1 Wind turbines. Part 25-4. Communications for monitoring and control of wind power plants. Mapping to XML based communication profile £18.00 members £36.00 non-members PEL/88 05/30137813 DC IEC 61400-25-5 ED 1 Wind turbines. Part 25-5. Communications for monitoring and control of wind power plants. Conformance testing PEL/88 05/30137839 DC ISO 3776-1 Tractors and machinery for agriculture. Seat belts. Part 1. Anchorage location requirements AGE/6 05/30137842 DC ISO 9679 Aerospace. Clamps for fluid systems. Test methods ACE/69 05/30137845 DC ISO 12319 Aerospace. Clamps 'P' (loop style). Procurement specification ACE/69 05/30137850 DC IEC 62215-2 Integrated circuits. Measurement of impulse immunity. Part 2. Impulse injection method EPL/47 05/30137873 DC EN 15315 Heating systems in buildings. Energy performance of buildings. Overall energy use, primary energy and CO$d2 emissions RHE/24 05/30137882 DC EN 15316-1 Heating systems in buildings. Method for calculation of system energy requirements and system efficiencies. Part 1. General RHE/24 05/30137885 DC EN 15316-3-1 Heating systems in buildings. Method for calculation of system energy requirements and system efficiencies. Part 3.1. Domestic hot water systems, characterisation of needs (tapping requirements) RHE/24 05/30137890 DC EN 15316-3-2 Heating systems in buildings. Method for calculation of system energy requirements and system efficiencies. Part 3.2. Domestic hot water systems, distribution RHE/24 05/30137893 DC EN 15316-3-3 Heating systems in buildings. Method for calculation of system energy requirements and system efficiencies. Part 3-3. Domestic hot water systems, generation RHE/24 05/30137922 DC ISO 13865-3 Safety of machinery. Pressure-sensitive protective devices. Part 3. General principles for the design and testing of pressure-sensitive bumpers, plates, wires and similar devices MCE/3 05/30137930 DC ISO 16100-4 Industrial automation systems and integration. Manufacturing software capability profiling for interoperability. Part 4. Conformance test methods, criteria and reports AMT/5 05/30137946 DC EN 15269-1 Extended application of test results for fire resistance for doorsets and shutter assemblies. For doors and windows. Part 1. General requirements for fire resistance FSH/22 05/30137949 DC EN 15269-3 Extended application of test results for fire resistance for doorsets and shutter assemblies. For doors and shutters. Part 3. Timber hinged and pivoted doorsets FSH/22 05/30137978 DC EN 15273-1 Railway applications. Gauges. Part 1. Generalities. Common rules for infrastructure and rolling stock RAE/1/-/12 05/30137981 DC EN 15273-2 Railway applications. Gauges. Part 2. Rolling stock gauges £18.00 members £36.00 non-members RAE/1/-/12 05/30138000 DC IEC 60155 AMD 2 Glow-starters for fluorescent lamps CPL/34/1 05/30138005 DC IEC 60079-14 ED 4 Electrical apparatus for explosive gas atmospheres. Part 14. Electrical installations in hazardous areas (other than mines) GEL/31/11 Page 44 of 69 DRAFT BRITISH STANDARDS FOR PUBLIC COMMENT 05/30138009 DC EN 15319 General principles of design of fibrous (gypsum) plaster works B/544/1 05/30138017 DC ISO/IEC 14471 Information technology. Software engineering. Guidelines for the adoption of CASE tools IST/15 Comments for the above document are required by 31 October, 2005 05/30138025 DC ISO/IEC 14102 Information technology. Guideline for the evaluation and selection of CASE tools IST/15 Comments for the above document are required by 31 October, 2005 05/30138030 DC ISO 2074 Plywood. Vocabulary B/541 05/30138051 DC EN 60335-2-79/prA1 Household and similar electrical appliances. Safety. Part 2-79. Particular requirements for high pressure cleaners and steam cleaners CPL/61/10 05/30138064 DC IEC CISPR16-1-1 AMD 2 ED 1 Specification for radio disturbance and immunity measuring apparatus methods. Part 1-1. Radio disturbance and immunity measuring apparatus. Selectivity of measuring receiver in the frequency range 1GHz to 18GHz GEL/210/12 05/30138070 DC IEC 60598-2-27 ED 1 Luminaires. Part 2-27. Luminaires for neon lamp and similar equipment CPL/34/4 05/30138085 DC IEC CISPR 16-2-1 AMD 2 ED 1 Specification for radio disturbance and immunity measuring apparatus and methods. Part 2-1. Methods of measurement of disturbance and immunity. Conducted disturbance measurements GEL/210/12 05/30138123 DC BS ISO 8836 Suction catheters for use in the respiratory tract CH/121/2 05/30138125 DC ISO 9911 Agricultural irrigation equipment. Manually operated small plastics valves AGE/30 05/30138145 DC BS 6172 AMD 1 Specification of installation of gas cooking appliances (1st, 2nd and 3rd family gases) GSE/30/-/10 05/30138148 DC EN 215:2004/prA1 Thermostatic radiator valves. Requirements and test methods RHE/16 Comments for the above document are required by 14 November, 2005 05/30138201 DC ISO 12696 Cathodic protection of steel in concrete ISE/NFE/8 05/30138208 DC ISO 9635-1 Agricultural irrigation equipment. Irrigation valves. Part 1. General requirements AGE/30 05/30138211 DC ISO 9635-2 Agricultural irrigation equipment. Irrigation valves. Part 2. Isolating valves AGE/30 05/30138214 DC ISO 9635-3 Agricultural irrigation equipment. Irrigation valves. Part 3. Check valves AGE/30 05/30138217 DC ISO 9635-4 Agricultural irrigation equipment. Irrigation valves. Part 4. Air valves AGE/30 05/30138220 DC ISO 9635-5 Agricultural irrigation equipment. Irrigation valves. Part 5. Control valves AGE/30 05/30138231 DC ISO 8407 Corrosion of metals and alloys. Removal of corrosion products from corrosion test specimens ISE/NFE/8 05/30138250 DC IEC CISPR 16-4-1 AMD 2 Specification for radio disturbance and immunity measuring apparatus and methods. Part 4-1. Uncertainties, statistics and limit modelling. Uncertainties in standardized EMC tests GEL/210/12 05/30138264 DC EN 12592 Bitumen and bituminous binders. Determination of solubility PTI/13 05/30138267 DC EN 1426 Bitumen and bituminous binders. Determination of needle penetration PTI/13 05/30138270 DC EN 12593 Bitumen and bituminous binders. Determination of the Fraass breaking point PTI/13 05/30138273 DC EN 1427 Bitumen and bituminous binders. Determination of the softening point. Ring and ball method PTI/13 05/30138276 DC EN 12595 Bitumen and bituminous binders. Determination of kinematic viscosity PTI/13 05/30138279 DC EN 12594 Bitumen and bituminous binders. Preparation of test samples PTI/13 05/30138282 DC EN 12596 Bitumen and bituminous binders. Determination of dynamic viscosity by vacuum capillary PTI/13 DRAFT BRITISH STANDARDS FOR PUBLIC COMMENT Page 45 of 69 05/30138285 DC EN 12606-1 Bitumen and bituminous binders. Determination of the paraffin wax content. Part 1. Method by distillation PTI/13 05/30138288 DC EN 12607-1 Bitumen and bituminous binders. Determination of the resistance to hardening under influence of heat and air. Part 1. RTFOT method PTI/13 05/30138291 DC EN 12607-2 Bitumen and bituminous binders. Determination of the resistance to hardening under influence of heat and air. Part 2. TFOT method PTI/13 05/30138294 DC EN 12607-3 Bitumen and bituminous binders. Determination of the resistance to hardening under influence of heat and air. Part 3. RFT method PTI/13 05/30138310 DC ISO 15882 ED 2 Sterilization of health care products. Chemical indicators. Guidance for selection, use and interpretation of results LBI/35 Comments for the above document are required by 18 October, 2005 05/30138350 DC EN 15322 Bitumen and bituminous binders. Framework for specifying cutback and fluxed bituminous binders PTI/13 05/30138353 DC EN 15323 Bitumen and bituminous binders. Accelerated long-term ageing conditioning by the rotating cylinder method (RCAT) PTI/13 05/30138357 DC EN 15324 Bitumen and bituminous binders. Determination of equiviscous temperature based on low shear viscosity using a dynamic shear rheometer in low frequency oscillation mode PTI/13 DOCUMENTS NOT ISSUED AS DPCs 05/30138360 DC EN 15325 Bitumen and bituminous binders. Determination of zero shear viscosity (ZSV) using a shear stress rheometer in creep mode PTI/13 05/30138363 DC EN 15326 Bitumen and bituminous binders. Measurement of density and specific gravity. Capillary-stoppered pyknometer method PTI/13 05/30138371 DC IEC 60068-2-27 ED 4 Basic environmental testing procedures. Part 2-27. Tests. Test Ea and guidance. Shock and bump GEL/104 05/30138375 DC IEC 60068-2-31 ED 2 Basic environmental testing procedures. Part 2-31. Tests. Test Ec. Rough handling shocks, primarily for equipment-type specimens GEL/104 05/30138385 DC EN 50440 Efficiency of domestic electrical storage water-heaters CPL/59 05/30138424 DC BS 8450 Code of practice for installation of electrical and electronic equipment in ships JPEL/18 05/30138425 DC ISO 4254-5 Agricultural machinery. Safety. Part 5. Power-driven soil-working equipment AGE/6 05/30138432 DC BS EN 1501-1 Refuse collection vehicles. General requirements and safety requirements. Part 1. Rear loaded refuse collection vehicles B/508/1 05/30138471 DC EN ISO 16276-2 Corrosion protection of steel structures by protective paint systems. Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a dry film. Part 2. Cross-cut testing and X-cut testing STI/27 05/30138485 DC EN 50469 Lightning protection systems. Symbols GEL/81 05/30138590 DC BS 6007 Electric cables. Single core unsheathed heat-resisting cables for voltages up to and including 450/750 V, for internal wiring GEL/20/17 05/30138592 DC BS 6231 Electric cables. 600/1000 V, PVC insulated cables for switchgear and controlgear wiring GEL/20/17 05/30138596 DC BS 6195 Electric cables. Insulated flexible cables and cords for coil leads GEL/20/17 DOCUMENTS NOT ISSUED AS DPCs BS EN 1994:Eurocode 4. Design of composite steel and concrete structures BS EN 1994-1:General rules BS EN 1994-1-2 Structural fire design This standard will shortly be prepared for publication. Please submit any comments to the committee secretary (below). Contact: Frank Thomas Email: [email protected] B/525/4 BS ISO 13357:Petroleum products. Determination of the filterability of lubricating oils Page 46 of 69 BS ISO 13357-2 Procedure for dry oils Copies of this document are available upon request from the committee secretary (below). Contact: Simon Merriman Email: [email protected] MCE/18/-/16 BS ISO 21148 Cosmetics. Microbiology. General instructions for microbiological examination Please direct any comments or queries regarding this forthcoming standard to the committee secretary (below). Contact: William Buckingham Email: [email protected] CW/217 prEN 2602 Aerospace series. Ports for adaptors, threaded, with lockring. Geometric configuration To view a copy of this document, which has now been issued as a Final Draft, please contact the committee secretary (below). Contact: Tracey Wilkins Email: [email protected] ACE/69 prEN 2603 Aerospace series. Port ends for adaptors, threaded, with lockring. Geometric configuration To view a copy of this document, which has now been issued as a Final Draft, please contact the committee secretary (below). Contact: Tracey Wilkins Email: [email protected] ACE/69 prEN 2604 Aerospace series. 8$0DC 30' interface for adaptors, threaded, with lockring. Geometric configuration To view a copy of this document, which has now been issued as a Final Draft, please contact the committee secretary (below). Contact: Tracey Wilkins Email: [email protected] ACE/69 prEN 2605 Aerospace series. 24$0DC interface for adaptors, threaded, with lockring. Geometric configuration To view a copy of this document, which has now been issued as a Final Draft, please contact the committee secretary (below). Contact: Tracey Wilkins Email: [email protected] ACE/69 prEN 2608 Aerospace series. Installation and removal requirements for 8$0DC 30' adaptors, threaded, with lockring To view a copy of this document, which has now been issued as a Final Draft, please contact the committee secretary (below). Contact: Tracey Wilkins Email: [email protected] ACE/69 prEN 2645 Aerospace series. Lockrings for adaptors, threaded, with lockring. Dimensions To view a copy of this document, which has now been issued as a Final Draft, please contact the committee secretary (below). Contact: Tracey Wilkins Email: [email protected] ACE/69 prEN 2713:Aerospace series. Cables, electrical, single and multicore for general purpose. Operating temperatures between -55$0DC and 200$0DC prEN 2713-003 Screened (spiral) and jacketed, ink jet printable. Product standard To view a copy of this document, which has now been issued as a Final Draft, please contact the committee secretary (below). Contact: Tracey Wilkins Email: [email protected] ACE/6/-/2 prEN 2713-007 Screened (spiral) and jacketed, UV laser printable. Product standard To view a copy of this document, which has now been issued as a Final Draft, please contact the committee secretary (below). Contact: Tracey Wilkins Email: [email protected] ACE/6/-/2 prEN 2714:Aerospace series. Cables, electrical, single and multicore for general purpose. Operating temperatures between -55$0DC and 260$0DC prEN 2714-007 Screened (spiral) and jacketed, UV laser printable. Product standard To view a copy of this document, which has now been issued as a Final Draft, please contact the committee secretary (below). Contact: Tracey Wilkins Email: [email protected] ACE/6/-/2 prEN 2714-013 DR family, screened (spiral) and jacketed, UV laser printable. Product standard To view a copy of this document, which has now been issued as a Final Draft, please contact the committee secretary (below). Contact: Tracey Wilkins Email: [email protected] ACE/6/-/2 prEN 4610 Aerospace series. Pipe coupling 8$0DC 30' in titanium alloy. Elbows 45$0DC, with thrust wire nut To view a copy of this document, which has now been issued as a Final Draft, please contact the committee secretary (below). Contact: Tracey Wilkins Email: [email protected] ACE/69 DOCUMENTS NOT ISSUED AS DPCs Page 47 of 69 prEN 15285 Agglomerated stone. Modular tiles for flooring (internal and external) This Draft European Standard has been issued by CEN for Enquiry with a closing date of 30 November, 2005. It will not be issued for public comment in the UK because it covers agglomerated stone as a generic product in which the UK has little or no interes Contact: David Fisher Email: [email protected] B/545 prEN 15286 Agglomerated stone. Slabs and tiles for wall finishes (internal and external) This Draft European Standard has been issued by CEN for Enquiry with a closing date of 30 November, 2005. It will not be issued for public comment in the UK because it covers agglomerated stone as a generic product in which the UK has little or no interes Contact: David Fisher Email: [email protected] B/545 prEN 45510:Guide for procurement of power station equipment prEN 45510-2:Electrical equipment prEN 45510-2-9 Cabling systems This Draft European Standard has been circulated by CEN/CENELEC at Enquiry stage. However, the UK committee responsible for input is dormant and it has therefore not been circulated for public comment. The text of the Enquiry Draft is nonetheless availabl Contact: Committee Service Centre Email: [email protected] E/-/20 ISO 6580:2005 General-purpose industrial fans. Circular flanges. Dimensions This International Standard has recently been published by ISO, and will shortly be implemented in the UK as a revision of dual-numbered standard BS 6339:1983 (ISO 6580:1981). Contact: Committee Service Centre Email: [email protected] MCE/17 ISO/IEC 15938:Information technology. Multimedia content description interface ISO/IEC 15938-4:2002/FPDAM 2 Audio This standard has been circulated to ISO members as a final committee draft by ISO/IEC JTC 1/SC 29. Copies of the text are available from the committee secretary (below), to whom comments should be submitted by 30 October, 2005. Contact: Jean Stride Email: [email protected] IST/37 prEN ISO 4925:Binders for paints and varnishes. Determination of softening point prEN ISO 4925-1:2005 Ring-and-ball method This Draft European Standard has already been implemented in the UK as BS ISO 4925-1:2004. Consequently the UK will support its adoption as a BS EN ISO standard. Contact: Committee Service Centre Email: [email protected] STI/3 prEN ISO 4925-2:2005 Cup-and-ball method This Draft European Standard has already been implemented in the UK as BS ISO 4925-2:2004. Consequently the UK will support its adoption as a BS EN ISO standard. Contact: Committee Service Centre Email: [email protected] STI/3 EN ISO 6141 Gas analysis. Requirements for certificates for calibration gases and gas mixtures This standard, which has not been issued as a Draft for Public Comment and is identical to ISO 6141:2000, has been circulated to CEN members for voting. Please submit any comments to the committee secretary (below) by 19 December, 2005. Contact: Sheila O'Reilly Email: sheila.o'[email protected] PTI/15 EN ISO 6143 Gas analysis. Comparison methods for determining and checking the composition of calibration gas mixtures This standard, which has not been issued as a Draft for Public Comment and is identical to ISO 6143:2001, has been circulated to CEN members for voting. Please submit any comments to the committee secretary (below) by 19 December, 2005. Contact: Sheila O'Reilly Email: sheila.o'[email protected] PTI/15 CEN/CENELEC UNIQUE ACCEPTANCE PROCEDURE BS EN 12961:2005 Flexible sheets for waterproofing. Bitumen, plastic and rubber sheets for roof waterproofing. Determination of resistance to impact The text of this Draft European Standard has been circulated for approval to publish by October 2005. Copies are available on request using document reference B/546.0036/05 from the committee secretary (below), to whom comments should be submitted by 30 Contact: Ray Kerrigan Email: [email protected] B/546 prEN 1854 Pressure sensing devices for gas burners and gas burning appliances Please direct any comments regarding this Draft European Standard to the committee secretary (below). Contact: Bernard Williams Email: [email protected] GSE/22/12 CEN/CENELEC UNIQUE ACCEPTANCE PROCEDURE Page 48 of 69 EN ISO 6144 Gas analysis. Preparation of calibration gas mixtures. Static volumetric method This standard, which has not been issued as a Draft for Public Comment and is identical to ISO 6144:2003, has been circulated to CEN members for voting. Please submit any comments to the committee secretary (below) by 19 December, 2005. Contact: Sheila O'Reilly Email: sheila.o'[email protected] PTI/15 prEN ISO 10283:2005 Binders for paints and varnishes. Determination of monomeric diisocyanates in polyisocyanate resins This Draft European Standard has already been implemented in the UK as BS 6782-10:1998. Consequently the UK will support its adoption as a BS EN ISO standard. Contact: Committee Service Centre Email: [email protected] STI/3 EN 12259:Fixed firefighting systems. Components for sprinkler and water spray systems EN 12259-1:1999/prA1:2001 Sprinklers This is a proposed amendment to normative annex B Test to determine operating temperatures of fusible link sprinklers and glass bulb sprinklers, specifically to the text of B.1 Apparatus & B.2 Procedure and to figure B.1, to address errors that have been Contact: Mike Hodson Email: [email protected] FSH/18/2 EN 12817:2002/prA1 LPG equipment and accessories. Inspection and requalification of LPG tanks up to and including 13 m$d3 overground This draft amendment has been circulated by CEN/286 under a shortened UAP procedure. A copy of the text may be obtained on request from the committee secretary (below). Contact: Tim Newins Email: [email protected] PVE/19 CEN EUROPEAN STANDARDS EN 12818:2002/prA1 LPG equipment and accessories. Inspection and requalification of LPG tanks up to and including 13 m$d3 underground This draft amendment has been circulated by CEN/286 under a shortened UAP procedure. A copy of the text may be obtained on request from the committee secretary (below). Contact: Tim Newins Email: [email protected] PVE/19 EN 13952:2003 LPG equipment and accessories. Filling procedures for LPG cylinders This draft amendment has been circulated by CEN/286 under a shortened UAP procedure. A copy of the text may be obtained on request from the committee secretary (below). Contact: Tim Newins Email: [email protected] PVE/19 prEN 14870:Petroleum and natural gas industries. Induction bends, fittings and flanges for pipeline transportation systems prEN 14870-3 Flanges The text of this ISO TC 67 SC 2 document has been issued by CEN TC 12. The UK participated actively in the preparation of the equivalent ISO publication, so it is accordingly proposed that a vote of acceptance be submitted in the CEN TC 12 ballot. Please Contact: Keith Seyde Email: [email protected] PSE/17 prEN ISO 15715:2005 Binders for paints and varnishes. Determination of turbidity This Draft European Standard has already been implemented in the UK as BS ISO 15715:2003. Consequently the UK will support its adoption as a BS EN ISO standard. Contact: Committee Service Centre Email: [email protected] STI/3 EN 492:Fibre-cement slates and fittings. Product specification and test methods AMENDMENT 1:August 2005 to EN 492:2004 £19.00 members £20.00 non-members B/542/4 EN 494:Fibre-cement profiled sheets and fittings. Product specification and test methods AMENDMENT 1:August 2005 to EN 494:2004 £19.00 members £20.00 non-members B/542/4 EN 681:Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications EN 681-1:Vulcanized rubber AMENDMENT 3:August 2005 to EN 681-1:1996 £19.00 members £20.00 non-members PRI/70 EN 681-2:Thermoplastic elastomers AMENDMENT 2:August 2005 to EN 681-2:2000 £19.00 members £20.00 non-members PRI/70 EN 681-3:Cellular materials of vulcanized rubber AMENDMENT 3:August 2005 to EN 681-3:2000 £19.00 members £20.00 non-members PRI/70 EN 681-4:Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications Part 4. Cast polyurethane sealing elements AMENDMENT 2:August 2005 to EN 681-4:2000 £19.00 members £20.00 non-members PRI/70 Page 49 of 69 CEN EUROPEAN STANDARDS EN 682:Elastomeric seals. Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids AMENDMENT 1:August 2005 to EN 682:2005 £19.00 members £20.00 non-members PRI/70 EN 695:2005 Kitchen sinks. Connecting dimensions £49.40 members £52.00 non-members B/503 EN 957:Stationary training equipment EN 957-1:2005 General safety requirements and test methods £60.80 members £64.00 non-members SW/136/4 EN 957-10:2005 Exercise bicycles with a fixed wheel or without freewheel, additional specific safety requirements and test methods £49.40 members £52.00 non-members SW/136/4 EN 1001:Durability of wood and wood-based products. Terminology EN 1001-2:2005 Vocabulary £133.00 members £140.00 non-members B/515 EN 1071:Advanced technical ceramics. Methods of test for ceramic coatings EN 1071-3:2005 Determination of adhesion and other mechanical failure modes by a scratch test £114.00 members £120.00 non-members RPI/13 EN 1097:Tests for mechanical and physical properties of aggregates CEN EUROPEAN STANDARDS EN 1097-9:Determination of the resistance to wear by abrasion from studded tyres. Nordic test AMENDMENT 1:August 2005 to EN 1097-9:1998 £19.00 members £20.00 non-members B/502/6 EN 1104:2005 Paper and board intended to come into contact with foodstuffs. Determination of the transfer of antimicrobial constituents £49.40 members £52.00 non-members CW/47/3 EN 1266:Independent gas-fired convection heaters incorporating a fan to assist transportation of combustion air and/or flue gases AMENDMENT 1:August 2005 to EN 1266:2002 £19.00 members £20.00 non-members GSE/36 EN 1504:Products and systems for the protection and repair of concrete structures. Definitions, requirements, quality control and evaluation of conformity EN 1504-1:2005 Definitions £49.40 members £52.00 non-members B/517/8 EN 1744:Tests for chemical properties of aggregates EN 1744-4:2005 Determination of water susceptibility of fillers for bituminous mixtures £60.80 members £64.00 non-members B/502 EN 1888:Child care articles. Wheeled child conveyances. Safety requirements and test methods AMENDMENT 1:August 2005 to EN 1888:2003 £19.00 members £20.00 non-members CW/39 EN 1888:Child care articles. Wheeled child conveyances. Safety requirements and test methods AMENDMENT 2:August 2005 to EN 1888:2003 £19.00 members £20.00 non-members CW/39 EN 1888:Child care articles. Wheeled child conveyances. Safety requirements and test methods. AMENDMENT 3:August 2005 to EN 1888:2003 £19.00 members £20.00 non-members CW/39 EN 2088:2005 Aerospace series. Aluminium alloy AL-P2014A-T4 or T42. Clad sheet and strip. 0,4 mm < or = a < or = 6 mm £49.40 members £52.00 non-members ACE/61/-/24 EN 2731:2005 Aerospace series. Magnesium alloy MG-C46001-T6. Sand casting £49.40 members £52.00 non-members ACE/61/-/24 EN 4204:2005 Aerospace series. Aluminium alloy AL-P8090-T841. Sheet. 0,6 mm