Approved Cylinder Standar Standard General Register Notes American and Canadian ASME VIII Div 1 CTC 8WC DOT 2P DOT 3A DOT 3AA 3AA/TC3AAM-139 DOL 3AL 3AL/TC-3ALM DOT 3B DOT DOT DOT 3E DOT 4AA 480 DOT 4B DOT 4BA DOT 4BW DOT 4E DOT 4L DOT 8 DOT 8AL DOT 39 DOT-SP 6517 DOT-SP 6668 DOT-SP 7235 DOT-SP 7542 DOT-SP 8725 DOT-SP 9634 DOT-SP 10227 DOT-SP 10915 DOT-SP 10945 DOT-SP 11953 Australian & New Zealand AS 1777-2005 AS/NZS 1841.1-2007 AS/NZS 1841.2-2007 AS/NZS 1841.3-2007 AS/NZS 1841.4-2007 AS/NZS 1841.5-2007 AS/NZS 1841.6-2007 AS/NZS 1841.7-2007 AS/NZS 1841.8-2007 AS 2278–2000 AS 2468-1989 AS 2469-2005 AS 2470-2005 AS 2527-2006 AS 2764 - 2002 AS 2875-1995 AS 3577-2006 British BS 5045-2:1989 BS 5045-7:2000 BS 5045-8:2000 BS EN 1964-1:2000 BS EN 1964-2:2001 BS EN 1975:2000 BS EN 12862:2000 BS EN 12205:2001 EN EN 3 EN 12245 (as amended by ERMA COP) EN 13110 - 2002 84/526/EEC EN 12862:2000 ISO ISO 9809-1:1999 ISO 9809-2:2000 ISO 11119-1 (As amended by ERMA approved code of practice) Approved Cylinder Standards Description 1. This register shows cylinder standards that may be used for newly manufactured cylinders. A manufactured or imported into New Zealand if it is designed to a standard that appears on this 2. Where a cylinder standard has been withdrawn by the respective standards authority the stan this list. If you are aware of an anomaly, please contact ERMA NZ. Pressure Vessels Welded steel cylinder with porous filling Non-refillable Seamless steel cylinder with a water capacity not over 1,000 pounds (453 kg) and a service pressure of at least 150 psig (1.03MPa) Seamless steel cylinder with a water capacity of not over 1,000 pounds (453 kg) and a service pressure of at least 150 psig (1.03Mpa) Seamless aluminum cylinder with a maximum water capacity of 1000 pounds (453 kg) and minimum service pressure of 150 psig. (1.03Mpa) Seamless steel cylinder with a water capacity of not over 1,000 pounds (453 kg) and a service pressure of at least 150 psig (1.03 MPa) to not over 500 psig (3.44 MPa). Seamless steel cylinder with an outside diameter not greater than 2 inches (50 mm) nominal, a length less than 2 feet (600 mm) and a service pressure of 1,800 psig (12.4 MPa). Welded steel cylinder having a water capacity not over 1,000 pounds (453 kg) water capacity and a service pressure of 480 psig. (3.3 MPa) Welded or brazed steel cylinder with longitudinal seams that are forged lapwelded or brazed and with water capacity not over 1,000 pounds (453 kg) and a service pressure of at least 150 psig (1.03 MPa) but not over 500 psig (3.44 MPa). Welded or brazed steel cylinder either spherical or cylindrical in shape, with a water capacity of 1,000 pounds or less and a service pressure of at least 225 and not over 500 psig. Welded or brazed steel cylinder either spherical or cylindrical in shape, with one circumferential seam and a water capacity of 1,000 pounds (453 kg) or less and a service pressure of at least 225 psig (1.5 MPa) and not over 500 psig (3.44 MPa). Welded aluminium cylinder with a water capacity of not over 1,000 pounds (453 kg) and a service pressure of at least 225 psig (1.5 MPa) to not over 500 psig (3.44 MPa). A DOT 4L cylinder is a fusion welded insulated cylinder with a water capacity not over 1,000 pounds (453 kg) water capacity and a service pressure of at least 40 psig (0.27 MPa) but not greater than 500 psig (3.44 MPa). Seamless cylinders with a service pressure of 250 psig (1.7 MPa) with porous fillings for acetylene. Seamless steel cylinder with a service pressure of 250 psig (1.7 MPa). The attachment of heads by welding or by brazing by dipping process and a welded circumferential body seam is authorized. Longitudinal seams are not authorized. Non-refillable seamless, welded, or brazed cylinder with a service pressure not to exceed 80 percent of the test pressure. Spherical pressure vessels are authorized Welded steel cylinders based on DOT 4BW for acetylene Insulated welded cylinders based on DOT 4L with a water capacity of 100 pounds (45.36 kg) Fibre reinforced compressed gas cylinders conforming to DOT FRP-2 Welded steel cylinders based on DOT 4BW with porous filling for acetylene Fibre reinforced plastic, hoop-wrapped aluminium cylinders conforming to DOT FRP-2 for transportation of certain non-liquefied compressed gases Fibre reinforced plastic full composite cylinders conforming to DOT FRP-1 Cryogenic cylinders for liquid oxygen based on DOT 4L Fully wrapped carbon-fibre reinforced aluminium lined cylinders conforming to DOT CFFC Fully wrapped carbon fibre reinforced aluminium lined cylinders based on DOT CFFC Welded steel cylinder based on DOT 4BW for non-liquefied and liquefied compressed gases w Zealand Aluminium cylinders for compressed gases – Seamless – 0.1 kg to 130 kg Portable fire extinguishers- General requirements Portable fire extinguishers - Specific requirements for water type extinguishers Portable fire extinguishers - Specific requirements for wet chemical type extinguishers Portable fire extinguishers - Specific requirements for foam type extinguishers Portable fire extinguishers - Specific requirements for powder type extinguishers Portable fire extinguishers - Specific requirements for carbon dioxide type extinguishers Portable fire extinguishers - Specific requirements for vaporizing liquid type extinguishers Portable fire extinguishers - Specific requirements for non-rechargeable type extinguishers Metal aerosol dispensers of capacity 50 mL to 1000 mL inclusive Steel cylinders for compressed gases – Brazed – 0.1 kg to 11 kg Steel cylinders for compressed gases – Welded two-piece construction – 0.1 kg to 150 kg Steel cylinders for compressed gases – Welded three-piece construction with longitudinal joint – 11 kg to 150 kg Cylinders for dissolved acetylene FRP Hoop Wrapped 0.1kg - 130kg Alloy steel cylinders for compressed gases – Seamless – 0.1 kg to 500 kg Steel cylinders for compressed gases – Welded – 150 kg to 500 kg Transportable gas containers. Specification for steel containers of 0.5 L up to 450 L water capacity with welded seams Transportable gas containers. Specification for seamless steel gas containers of water capacity 0.5 L up to 15 L for special portable application Transportable gas containers. Specification for seamless aluminium alloy gas containers of water capacity 0.5 L up to 15 L and up to 300 bar charged pressure at 15°C for special portable application Transportable gas cylinders. Specification for the design and construction of refillable transportable seamless steel gas cylinders of water capacities from 0,5 litre up to and including 150 litres. Cylinders made of seamless steel with a value of less than 1100 MPa Transportable gas cylinders. Specification for the design and construction of refillable transportable seamless steel gas cylinders of water capacities from 0,5 litre up to and including 150 litres. Cylinders made of seamless steel with a value of 1100 MPa and above Transportable gas cylinders. Specification for the design and construction of refillable transportable seamless aluminium and aluminium alloy gas cylinders of capacity from 0,5 litre up to 150 litre Transportable gas cylinders. Specification for the design and construction of refillable transportable welded aluminium alloy gas cylinders Non-refillable cylinders Portable Fire Extinguishers Fully Wrapped Composite Cylinders Welded Aluminium LPG Cylinders Seamless unalloyed aluminium and aluminium alloy gas cylinders with capacity between 0.5 to 150 litres Transportable gas cylinders. Specification for the design and construction of refillable transportable welded aluminium alloy gas cylinders Cylinders of seamless steel of tensile strength less than 1100Mpa Cylinders of seamless steel of tensile strength greater than or equal to 1100Mpa Gas Cylinders of composite construction – Specification and test methods – Part 1: Hoop wrapped composite gas cylinders. er Standards Notes e used for newly manufactured cylinders. A cylinder can only be esigned to a standard that appears on this list. the respective standards authority the standard should not appear on act ERMA NZ. Acetylene LPG, to 787 ml, id to 80mm SCUBA SCUBA SCUBA Acetylene Acetylene US Department of Transportation permit expires 31 May 2010 Refer to ERMA approved code of practice HSNOCOP7-1 Department of Transportation permit expires 31 December 2010 US Department of Transportation permit expires 31 May 2010 US Department of Transportation permit expires 31 August 2010 US US Department of Transportation permit expires 31 December 2010 US Department of Transportation permit expires 31 May 2010 US Department of Transportation permit expires 30 November 2009 US Department of Transportation permit expires 28 February 2010 US Department of Transportation permit expires 30 September 2009 See R11 of the Hazardous Substances (Compressed Gases) Regulations 2004 See R24 of the Hazardous Substances (Compressed Gases) Regulations 2004 Declared obsolescent by Standards Australia Acetylene Supersedes B114 Partially replaced by BS EN 13322-1:2003 Together with BS EN 1964-1:2000 supersedes BS 5045-1:1982. Replaces BS 5045-3:1984 Replaces withdrawn standard BS 5045-1:1982 This standard must be used in accordance with the ERMA approved code of practice "Non-refillable cylinders manufactured to BS EN 12205: 2001 This standard must be used in accordance with the ERMA approved Gas Cylinders of Composite Construction Designed to EN 12245:2009 Identical to BS EN 12862 0.5 litre up to and including 150 litres 0.5 litre up to and including 150 litres This standard must be used in accordance with the ERMA approved Code of Practice for Gas Cylinders of Composite Construction Designed to ISO 111191